Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio and display receiver assembly.

WIRING DIAGRAM

E282609E26
1.031,0.344 1.865,0.542 0.833,0.198 10 false from Battery 0.49,0.813 1.854,1 1.365,0.188 10 false from IG1 NO. 1 Relay 0.802,1.302 1.906,1.5 1.104,0.198 10 false from ACC Relay 3.146,0.521 3.917,0.698 0.771,0.177 10 false RAD NO.1 2.917,0.969 4.302,1.198 1.385,0.229 10 false ECU-IG NO.2 3.198,1.5 3.969,1.677 0.771,0.177 10 false ACC 5.344,0.823 5.792,1 0.448,0.177 10 false H51 5.333,1.74 5.781,1.917 0.448,0.177 10 false H49 5.417,0.156 5.563,0.354 0.146,0.198 10 false 4 5.406,0.615 5.552,0.813 0.146,0.198 10 false 1 5.427,1.104 5.573,1.302 0.146,0.198 10 false 3 5.427,1.542 5.573,1.74 0.146,0.198 10 false 7 5.729,1.781 6.177,1.958 0.448,0.177 10 false GND1 5.729,1.323 6.177,1.5 0.448,0.177 10 false ACC1 5.719,0.844 6.167,1.021 0.448,0.177 10 false IG 5.708,0.385 6.156,0.563 0.448,0.177 10 false +B1 5.531,2.219 6.76,2.594 1.229,0.375 10 false Radio and Display Receiver Assembly 5.344,1.313 5.792,1.49 0.448,0.177 10 false H49 5.344,0.354 5.792,0.531 0.448,0.177 10 false H49

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U149461E01
0.03,0.056 0.438,0.240 0.408,0.184 10 *a 1.508,0.376 1.867,0.560 0.359,0.184 10 H49 2.517,0.427 2.927,0.611 0.410,0.184 10 ACC1 2.788,0.845 3.100,1.029 0.312,0.184 10 +B1 2.008,1.134 2.228,0.51 2.228,0.51 2.494,0.51 false 2.012,1.974 2.420,2.158 0.408,0.184 10 GND1 1.548,1.639 1.723,2.057 1.723,2.057 1.989,2.057 false 2.266,1.13 2.513,0.932 2.513,0.932 2.779,0.932 false 1.56,2.433 1.919,2.617 0.359,0.184 10 H51 0.193,2.707 0.424,2.890 0.231,0.184 10 IG 0.777,3.411 0.597,2.794 0.597,2.794 0.451,2.794 false

Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H49-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H49-4 (+B1) - Body ground Always 11 to 14 V
H49-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
H51-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR