Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Stereo Component Amplifier Power Source Circuit  


DESCRIPTION

This circuit provides power to the stereo component amplifier assembly.

WIRING DIAGRAM

E283657E05
5.625,0.365 5.938,0.563 0.313,0.198 10 false +B 5.24,0.385 5.635,0.583 0.396,0.198 10 false H67 5.313,0.167 5.708,0.365 0.396,0.198 10 false 1 5.625,0.938 5.938,1.135 0.313,0.198 10 false +B2 5.229,0.938 5.625,1.135 0.396,0.198 10 false H67 5.271,0.719 5.667,0.917 0.396,0.198 10 false 16 5.635,1.521 6.083,1.75 0.448,0.229 10 false ACC 5.208,3.146 5.604,3.344 0.396,0.198 10 false H67 5.271,1.281 5.667,1.479 0.396,0.198 10 false 12 5.615,3.135 6.083,3.344 0.469,0.208 10 false GND 5.313,2.917 5.708,3.115 0.396,0.198 10 false 3 5.208,3.625 5.604,3.823 0.396,0.198 10 false H67 5.24,3.406 5.635,3.604 0.396,0.198 10 false 18 5.615,3.625 6.083,3.833 0.469,0.208 10 false GND2 2.74,0.542 3.469,0.74 0.729,0.198 10 false RAD NO.2 2.938,1.094 3.667,1.292 0.729,0.198 10 false AMP 2.948,1.667 3.677,1.865 0.729,0.198 10 false ACC 5.229,1.521 5.625,1.719 0.396,0.198 10 false H63 0.573,0.385 1.802,0.635 1.229,0.25 10 false from Battery 0.375,1.521 1.604,1.771 1.229,0.25 10 false from ACC Relay 5.167,4.104 6.896,4.51 1.729,0.406 10 false Stereo Component Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U148133E01
0.047,0.037 0.237,0.214 0.190,0.177 10 *a 1.317,0.282 1.666,0.459 0.350,0.177 10 GND 1.557,1.945 1.855,2.122 0.298,0.177 10 H63 0.051,0.425 0.263,0.602 0.212,0.177 10 +B 1.021,0.859 1.119,0.367 1.119,0.367 1.295,0.367 false 2.878,2.173 3.228,2.350 0.350,0.177 10 ACC 2.473,2.718 2.681,2.258 2.681,2.258 2.857,2.258 false 1.351,1.379 1.794,1.556 0.442,0.177 10 GND2 1.021,1.061 1.154,1.464 1.154,1.464 1.33,1.464 false 0.747,0.875 0.472,0.518 0.472,0.518 0.296,0.518 false 0.051,1.411 0.332,1.588 0.281,0.177 10 +B2 0.764,1.061 0.557,1.504 0.557,1.504 0.381,1.504 false 2.053,0.236 2.351,0.413 0.298,0.177 10 H67

Disconnect the stereo component amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H67-3 (GND) - Body ground Always Below 1 Ω
H67-18 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H67-1 (+B) - Body ground Always 11 to 14 V
H67-18 (+B2) - Body ground Always 11 to 14 V
H63-12 (ACC) - Body ground Ignition switch ACC 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR