Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

The radio and display receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from speakers even if there is no malfunction in the stereo component amplifier assembly, DCM (telematics transceiver)* or speakers.

*: w/ Manual (SOS) Switch


WIRING DIAGRAM

E284138E06
5.667,3.469 6.125,3.667 0.458,0.198 10 false H63 5.667,3.635 6.844,4.052 1.177,0.417 10 false Stereo Component Amplifier Assembly 5.979,0.615 6.438,0.813 0.458,0.198 10 false R+ 5.969,1.208 6.427,1.406 0.458,0.198 10 false R- 5.979,1.802 6.438,2 0.458,0.198 10 false L+ 5.979,2.396 6.438,2.594 0.458,0.198 10 false L- 5.969,3 6.427,3.198 0.458,0.198 10 false SLD 5.75,0.5 6.208,0.698 0.458,0.198 10 false 5 5.75,1.083 6.208,1.281 0.458,0.198 10 false 4 5.75,1.688 6.208,1.885 0.458,0.198 10 false 3 5.76,2.281 6.219,2.479 0.458,0.198 10 false 2 5.76,2.865 6.219,3.063 0.458,0.198 10 false 6 3.302,3.156 4.177,3.354 0.875,0.198 10 false Shielded 1.333,0.51 1.792,0.708 0.458,0.198 10 false 1 1.344,1.094 1.802,1.292 0.458,0.198 10 false 5 1.344,1.698 1.802,1.896 0.458,0.198 10 false 2 1.354,2.281 1.813,2.479 0.458,0.198 10 false 6 0.938,0.635 1.396,0.833 0.458,0.198 10 false FR+ 0.969,1.208 1.427,1.406 0.458,0.198 10 false FR- 0.979,1.802 1.438,2 0.458,0.198 10 false FL+ 0.979,2.417 1.438,2.615 0.458,0.198 10 false FL- 0.26,3.427 0.719,3.625 0.458,0.198 10 false H49 0.25,3.594 1.438,4.01 1.188,0.417 10 false Radio and Display Receiver Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H63 stereo component amplifier assembly connector.


b.

Disconnect the H49 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H49-1 (FR+) - H63-5 (R+) Always Below 1 Ω
H49-2 (FL+) - H63-3 (L+) Always Below 1 Ω
H49-5 (FR-) - H63-4 (R-) Always Below 1 Ω
H49-6 (FL-) - H63-2 (L-) Always Below 1 Ω
H63-6 (SLD) - Body ground Always 10 kΩ or higher
H49-1 (FR+) - Body ground Always 10 kΩ or higher
H49-2 (FL+) - Body ground Always 10 kΩ or higher
H49-5 (FR-) - Body ground Always 10 kΩ or higher
H49-6 (FL-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR