Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2015.06–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

This circuit provides power to the navigation receiver assembly.

WIRING DIAGRAM

E282609E27
5.521,2.115 6.74,2.49 1.219,0.375 10 false Navigation Receiver Assembly 5.719,0.323 6.104,0.49 0.385,0.167 10 false +B1 5.719,1.708 6.26,1.875 0.542,0.167 10 false GND1 5.719,1.271 6.354,1.438 0.635,0.167 10 false ACC1 5.719,0.781 6.104,0.948 0.385,0.167 10 false IG 5.344,1.74 5.698,1.906 0.354,0.167 10 false H54 5.344,0.354 5.698,0.521 0.354,0.167 10 false H54 5.344,0.813 5.698,0.979 0.354,0.167 10 false H56 5.344,1.302 5.698,1.469 0.354,0.167 10 false H54 5.427,0.125 5.563,0.292 0.135,0.167 10 false 4 5.438,1.521 5.573,1.688 0.135,0.167 10 false 7 5.427,0.583 5.542,0.75 0.115,0.167 10 false 1 5.427,1.083 5.542,1.25 0.115,0.167 10 false 3 3.167,1.479 3.521,1.656 0.354,0.177 10 false ACC 2.885,0.979 3.813,1.156 0.927,0.177 10 false ECU-IG NO. 2 3.042,0.51 3.823,0.688 0.781,0.177 10 false RAD NO. 1 1,0.302 1.833,0.479 0.833,0.177 10 false from Battery 0.531,0.76 1.833,0.979 1.302,0.219 10 false from IG NO. 1 Relay 0.802,1.25 1.833,1.458 1.031,0.208 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170707E02
2.156,0.823 2.49,0.823 true 1.948,0.771 2.083,0.417 2.083,0.417 2.333,0.417 true 1.615,1.083 1.5,1.417 1.5,1.417 1.25,1.417 true 1.083,2.458 1,2 1,2 0.75,2 true 0.135,0.052 0.313,0.208 0.177,0.156 10 false *a 2.5,0.76 2.885,0.917 0.385,0.156 10 false +B1 0.844,1.344 1.333,1.521 0.49,0.177 10 false GND1 0.448,0.76 0.833,0.917 0.385,0.156 10 false H54 2.396,0.323 2.917,0.479 0.521,0.156 10 false ACC1 0.583,1.917 0.969,2.073 0.385,0.156 10 false IG 0.448,2.229 0.833,2.385 0.385,0.156 10 false H56

Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H54-4 (+B1) - Body ground Always 11 to 14 V
H54-3 (ACC1) - Body ground Engine switch on (ACC) 11 to 14 V
H56-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR