Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260992 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio and display receiver assembly.

WIRING DIAGRAM

E282609E24
5.458,2.115 6.813,2.469 1.354,0.354 10 false Radio and Display Receiver Assembly 5.719,0.354 6.104,0.521 0.385,0.167 10 false +B1 5.719,1.74 6.26,1.906 0.542,0.167 10 false GND1 5.719,1.302 6.354,1.469 0.635,0.167 10 false ACC1 5.719,0.813 6.104,0.979 0.385,0.167 10 false IG 5.344,1.74 5.698,1.906 0.354,0.167 10 false H49 5.344,0.354 5.698,0.521 0.354,0.167 10 false H49 5.344,0.813 5.698,0.979 0.354,0.167 10 false H51 5.344,1.302 5.698,1.469 0.354,0.167 10 false H49 5.427,0.125 5.563,0.292 0.135,0.167 10 false 4 5.438,1.521 5.573,1.688 0.135,0.167 10 false 7 5.427,0.583 5.542,0.75 0.115,0.167 10 false 1 5.427,1.083 5.542,1.25 0.115,0.167 10 false 3 3.167,1.469 3.521,1.646 0.354,0.177 10 false ACC 2.885,0.958 3.813,1.135 0.927,0.177 10 false ECU-IG NO. 2 3.042,0.49 3.823,0.667 0.781,0.177 10 false RAD NO. 1 1,0.302 1.833,0.479 0.833,0.177 10 false from Battery 0.479,0.76 1.865,0.979 1.385,0.219 10 false from IG1 NO. 1 Relay 0.802,1.25 1.833,1.458 1.031,0.208 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170708E01
0.134,0.054 0.307,0.211 0.173,0.158 10 *a 2.51,1.023 2.895,1.181 0.385,0.158 10 +B1 0.629,1.367 1.070,1.524 0.441,0.158 10 GND1 0.41,0.739 0.799,0.897 0.389,0.158 10 H49 2.27,0.423 2.793,0.581 0.523,0.158 10 ACC1 2.129,0.843 2.481,1.066 false 1.953,0.771 2.239,0.523 false 1.615,1.051 1.122,1.4 false 0.576,2.607 0.965,2.765 0.389,0.158 10 IG 1.065,2.52 0.805,2.661 false 0.393,2.212 0.781,2.369 0.389,0.158 10 H51

Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H49-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H49-4 (+B1) - Body ground Always 11 to 14 V
H49-3 (ACC1) - Body ground Engine switch on (ACC) 11 to 14 V
H51-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR