Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Multi-display) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261004 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Multi-display) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Multi-display)  Park / Neutral Position Switch Circuit  


DESCRIPTION

This circuit sends the park/neutral position switch assembly signals to the clearance warning ECU.

WIRING DIAGRAM

E202337E12
5.521,2.125 7.104,2.604 1.583,0.479 10 false Clearance Warning ECU 5.521,1.958 5.677,2.146 0.156,0.188 10 false I1 2.635,1.229 2.875,1.417 0.24,0.188 10 false RB 4.042,1.25 4.281,1.438 0.24,0.188 10 false RL 5.958,1.104 6.198,1.292 0.24,0.188 10 false RL 4.385,0.979 4.521,1.167 0.135,0.188 10 false 1 2.427,0.99 2.552,1.177 0.125,0.188 10 false 2 5.594,0.979 5.792,1.167 0.198,0.188 10 false 13 0.198,1.115 1.385,1.5 1.188,0.385 10 false from ECU-IG NO.1 Fuse 2.625,1.542 2.948,1.698 0.323,0.156 10 false C40 2.625,1.708 4.063,2.135 1.438,0.427 10 false Park/Neutral Position Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
E179071E09
0.582,0.73 0.821,0.914 0.239,0.184 10 RB 2.892,0.591 3.131,0.775 0.239,0.184 10 RL 1.653,1.119 0.852,0.823 false 2.05,1.234 2.844,0.67 false

Disconnect the C40 park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (RL) - 2 (RB) Shift lever in R Below 1 Ω
1 (RL) - 2 (RB) Shift lever not in R 10 kΩ or higher


Result
Result Proceed to
OK A
NG (for A750F) B
NG (for AC60F) C



A

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)

B

C

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)
a.
U149197E01
0.068,0.04 0.316,0.223 0.248,0.184 10 *a 1.578,0.511 1.870,0.677 0.291,0.166 10 C40 2.584,0.79 2.823,0.937 0.239,0.147 10 RB 1.837,1.286 2.264,0.847 2.264,0.847 2.562,0.848 false

Disconnect the C40 park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C40-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - PARK/NEUTRAL POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the I1 clearance warning ECU connector.


b.

Disconnect the C40 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-13 (RL) - C40-1 (RL) Always Below 1 Ω
I1-13 (RL) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR