Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/o Multi-display) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261004 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Multi-display) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/o Multi-display)  Indicator Circuit  


DESCRIPTION

The warning indicator lights are installed in the clearance warning indicator assembly.

WIRING DIAGRAM

E194318E05
5.773,1.761 6.031,1.963 0.258,0.202 10 L3 2.936,2.816 3.416,3.018 0.480,0.202 10 G160 2.936,3.002 4.186,3.367 1.250,0.364 10 Clearance Warning Indicator Assembly 5.646,2.843 5.904,3.046 0.258,0.202 10 I1 5.773,1.194 6.031,1.396 0.258,0.202 10 L5 5.773,0.627 6.031,0.829 0.258,0.202 10 L6 3.911,1.761 4.169,1.963 0.258,0.202 10 RL 3.077,1.502 3.335,1.704 0.258,0.202 10 BD 1.811,1.661 2.751,1.863 0.940,0.202 10 ECU-IG NO. 2 0.143,1.502 1.447,1.704 1.304,0.202 10 from Ignition Switch 3.911,1.194 4.169,1.396 0.258,0.202 10 BK 3.911,0.627 4.169,0.829 0.258,0.202 10 OP 5.46,1.1 5.662,1.302 0.202,0.202 10 19 5.46,1.652 5.711,1.854 0.251,0.202 10 17 5.46,0.504 5.662,0.706 0.202,0.202 10 20 4.277,1.1 4.451,1.302 0.174,0.202 10 15 4.277,1.652 4.451,1.854 0.174,0.202 10 14 2.843,1.402 3.017,1.605 0.174,0.202 10 9 5.773,2.324 6.031,2.526 0.258,0.202 10 L1 3.911,2.324 4.169,2.526 0.258,0.202 10 RR 5.46,2.224 5.697,2.427 0.237,0.202 10 15 4.277,2.224 4.451,2.427 0.174,0.202 10 5 4.277,0.504 4.451,0.706 0.174,0.202 10 1 5.646,3.03 6.905,3.377 1.259,0.346 10 Clearance Warning ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING INDICATOR - BATTERY)
a.
U170670E01
0.487,0.696 0.862,0.854 0.375,0.158 10 G160 0.483,1.541 0.723,1.685 0.240,0.144 10 BD 0.025,0.017 0.195,0.173 0.170,0.156 10 *a 1.252,1.323 0.779,1.618 false

Disconnect the G160 clearance warning indicator assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G160-9 (BD) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning Indicator Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - CLEARANCE WARNING INDICATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - CLEARANCE WARNING INDICATOR)
a.

Disconnect the I1 clearance warning ECU connector.


b.

Disconnect the G160 clearance warning indicator light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-15 (L1) - G160-5 (RR) Always Below 1 Ω
I1-17 (L3) - G160-14 (RL) Always Below 1 Ω
I1-19 (L5) - G160-15 (BK) Always Below 1 Ω
I1-20 (L6) - G160-1 (OP) Always Below 1 Ω
I1-15 (L1) - Body ground Always 10 kΩ or higher
I1-17 (L3) - Body ground Always 10 kΩ or higher
I1-19 (L5) - Body ground Always 10 kΩ or higher
I1-20 (L6) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR