Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261016 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) U

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  TERMINALS OF ECU  


*1: for Navigation Receiver Type

*2: for Radio and Display Type


REAR TELEVISION CAMERA ASSEMBLY (w/ Tire Carrier)


U170739E02
3.51,0.125 3.792,0.302 0.281,0.177 10 false v3

a.

Disconnect the v3 rear television camera assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
v3-6 (CB+) - Body ground B - Body ground Power source Engine switch on (ACC) 5.5 to 7.05 V
v3-5 (CGND) - Body ground BR - Body ground Shield ground Always Below 1 Ω


c.

Reconnect the v3 rear television camera assembly connector.


d.

Measure the waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
v3-3 (CV+) - v3-2 (CV-) R - W Video signal Engine starts, shift lever in R, camera lens not covered, displaying image Pulse generation
(Refer to waveform 1)
Engine starts, shift lever in R, camera lens covered, blacking out screen Pulse generation
(Refer to waveform 2)

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.



e.
E265840E07
1.271,1.469 1.531,2.052 false 1.125,1.573 0.896,2.042 false 1.344,3.531 1.667,4.219 false 1.156,3.594 0.865,4.219 false 0.063,0.073 0.26,0.26 0.198,0.188 10 false *a 0.063,2.198 0.26,2.385 0.198,0.188 10 false *b 0.323,1.021 0.667,1.188 0.344,0.167 10 false GND 0.333,3.198 0.677,3.365 0.344,0.167 10 false GND 0.771,2.063 0.969,2.25 0.198,0.188 10 false *c 1.49,2.063 1.688,2.25 0.198,0.188 10 false *d 1.635,4.24 1.833,4.427 0.198,0.188 10 false *d 0.729,4.208 0.927,4.396 0.198,0.188 10 false *c

Reference (Oscilloscope waveform):

Text in Illustration
*a Waveform 1
*b Waveform 2
*c Synchronized Signal
*d Video Waveform

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.


i.

Waveform

Measurement Condition
Item Content
Measurement terminal v3-3 (CV+) - v3-2 (CV-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Engine starts, shift lever in R, camera lens is not covered, displaying an image
Waveform 2: Engine starts, shift lever in R, camera lens is covered, blacking out the screen

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).






REAR TELEVISION CAMERA ASSEMBLY (w/o Tire Carrier)


U170740E02
3.469,0.125 3.75,0.302 0.281,0.177 10 false X10

a.

Disconnect the X10 rear television camera assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X10-6 (CB+) - Body ground B - Body ground Power source Engine switch on (ACC) 5.5 to 7.05 V
X10-5 (CGND) - Body ground BR - Body ground Shield ground Always Below 1 Ω


c.

Reconnect the X10 rear television camera assembly connector.


d.

Measure the waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X10-3 (CV+) - X10-2 (CV-) R - W Video signal Engine starts, shift lever in R, camera lens not covered, displaying image Pulse generation
(Refer to waveform 1)
Engine starts, shift lever in R, camera lens covered, blacking out screen Pulse generation
(Refer to waveform 2)

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.



e.
E265840E08
1.271,1.469 1.531,2.052 false 1.125,1.573 0.896,2.042 false 1.344,3.521 1.667,4.208 false 1.156,3.594 0.865,4.219 false 0.063,0.01 0.26,0.198 0.198,0.188 10 false *a 0.063,2.208 0.26,2.396 0.198,0.188 10 false *b 0.323,0.969 0.667,1.135 0.344,0.167 10 false GND 0.333,3.146 0.677,3.313 0.344,0.167 10 false GND 0.771,2.031 0.969,2.219 0.198,0.188 10 false *c 1.49,2.073 1.688,2.26 0.198,0.188 10 false *d 1.635,4.24 1.833,4.427 0.198,0.188 10 false *d 0.729,4.219 0.927,4.406 0.198,0.188 10 false *c

Reference (Oscilloscope waveform):

Text in Illustration
*a Waveform 1
*b Waveform 2
*c Synchronized Signal
*d Video Waveform

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.


i.

Waveform 1

Measurement Condition
Item Content
Measurement terminal X10-3 (CV+) - X10-2 (CV-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Engine starts, shift lever in R, camera lens is not covered, displaying an image
Waveform 2: Engine starts, shift lever in R, camera lens is covered, blacking out the screen

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).






NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


U170746E03
4.292,0.938 4.604,1.083 0.313,0.146 10 false H56 5.802,1.292 6.115,1.438 0.313,0.146 10 false RA 3.177,0.938 3.49,1.083 0.313,0.146 10 false H57 2.115,0.948 2.427,1.094 0.313,0.146 10 false H55 0.854,1.896 1.167,2.042 0.313,0.146 10 false H54 1.823,1.896 2.135,2.042 0.313,0.146 10 false H53 5.354,2.198 5.667,2.344 0.313,0.146 10 false H58 5.74,0.438 6.042,0.635 0.302,0.198 10 false DB

a.

Measure the voltage, resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H55-11 (CA+) - H55-23 (CGND) B - Shielded Rear television camera assembly power supply Engine switch on (ACC) 5.5 to 7.05 V
H55-12 (V+) - H55-24 (V-) R - W Video signal Engine starts, shift lever in R, camera lens not covered, displaying image Pulse generation
(Refer to waveform 1)
Engine starts, shift lever in R, camera lens covered, blacking out screen Pulse generation
(Refer to waveform 2)
H55-24 (V-) - H55-23 (CGND) W - Shielded Ground Always Below 1 Ω
H56-2 (REV) - H54-7 (GND1) R - BR Reverse signal See "Vehicle Signal Check Mode" in Operation Check (See page (Click here)) -
H56-17 (SPD) - H54-7 (GND1) R - BR Speed signal from combination meter assembly See "Vehicle Signal Check Mode" in Operation Check (See page (Click here)) -

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.



b.
E265840E09
1.271,1.469 1.531,2.052 false 1.125,1.573 0.896,2.042 false 1.344,3.531 1.667,4.219 false 1.156,3.594 0.865,4.219 false 0.063,0.01 0.26,0.198 0.198,0.188 10 false *a 0.063,2.156 0.26,2.344 0.198,0.188 10 false *b 0.323,0.969 0.667,1.135 0.344,0.167 10 false GND 0.333,3.146 0.677,3.313 0.344,0.167 10 false GND 0.771,2.052 0.969,2.24 0.198,0.188 10 false *c 1.49,2.073 1.688,2.26 0.198,0.188 10 false *d 1.635,4.24 1.833,4.427 0.198,0.188 10 false *d 0.729,4.208 0.927,4.396 0.198,0.188 10 false *c

Reference (Oscilloscope waveform):

Text in Illustration
*a Waveform 1
*b Waveform 2
*c Synchronized Signal
*d Video Waveform

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


i.

Waveform

Measurement Condition
Item Content
Measurement terminal H55-12 (V+) - H55-24 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Engine starts, shift lever in R, camera lens is not covered, displaying an image
Waveform 2: Engine starts, shift lever in R, camera lens is covered, blacking out the screen

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).






RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


U170748E03
4.292,0.948 4.604,1.094 0.313,0.146 10 false H51 5.792,1.271 6.104,1.417 0.313,0.146 10 false RA 3.167,0.938 3.479,1.083 0.313,0.146 10 false H52 2.115,0.938 2.427,1.083 0.313,0.146 10 false H50 0.854,1.896 1.167,2.042 0.313,0.146 10 false H49 1.833,1.896 2.146,2.042 0.313,0.146 10 false H48 5.354,2.208 5.667,2.354 0.313,0.146 10 false H69 4.094,2.344 4.406,2.49 0.313,0.146 10 false z10 2.729,2.031 3.042,2.177 0.313,0.146 10 false z12 5.74,0.427 6.042,0.625 0.302,0.198 10 false DB

a.

Measure the voltage, resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H50-11 (CA+) - H50-23 (CGND) B - Shielded Rear television camera assembly power supply Engine switch on (ACC) 5.5 to 7.05 V
H50-12 (V+) - H50-24 (V-) R - W Video signal Engine starts, shift lever in R, camera lens not covered, displaying image Pulse generation
(Refer to waveform 1)
Engine starts, shift lever in R, camera lens covered, blacking out screen Pulse generation
(Refer to waveform 2)
H50-24 (V-) - H50-23 (CGND) W - Shielded Ground Always Below 1 Ω
H51-2 (REV) - H49-7 (GND1) R - BR Reverse signal See "Vehicle Signal Check Mode" in Operation Check (See page (Click here)) -
H51-17 (SPD) - H49-7 (GND1) R - BR Speed signal from combination meter assembly See "Vehicle Signal Check Mode" in Operation Check (See page (Click here)) -

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.



b.
E265840E10
1.271,1.469 1.531,2.052 false 1.125,1.573 0.896,2.042 false 1.344,3.531 1.667,4.219 false 1.156,3.594 0.865,4.219 false 0.063,0.01 0.26,0.198 0.198,0.188 10 false *a 0.063,2.156 0.26,2.344 0.198,0.188 10 false *b 0.323,0.969 0.667,1.135 0.344,0.167 10 false GND 0.333,3.146 0.677,3.313 0.344,0.167 10 false GND 0.771,2.042 0.969,2.229 0.198,0.188 10 false *c 1.49,2.063 1.688,2.25 0.198,0.188 10 false *d 1.635,4.229 1.833,4.417 0.198,0.188 10 false *d 0.729,4.219 0.927,4.406 0.198,0.188 10 false *c

Reference (Oscilloscope waveform):

Text in Illustration
*a Waveform 1
*b Waveform 2
*c Synchronized Signal
*d Video Waveform

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


i.

Waveform

Measurement Condition
Item Content
Measurement terminal H50-12 (V+) - H50-24 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Engine starts, shift lever in R, camera lens is not covered, displaying an image
Waveform 2: Engine starts, shift lever in R, camera lens is covered, blacking out the screen

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).