Home › Power Source / Network › 5L-E (BATTERY / CHARGING) › GENERATOR
RM27T0E _57 Power Source / Network _053723 5L-E BATTERY / CHARGING _0261017 GENERATOR A

5L-E BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 29300 1.INSPECT GENERATOR WITH VACUUM PUMP ASSEMBLY

a.

Mount the generator in a vise between aluminum plates.


b.
A220268

Insert a screwdriver to hold the generator rotor.


c.

Install a bolt and nut to the outside of the pulley so that the bolt head and nut clamp the pulley, and then position a dial indicator as shown in the illustration.


d.

Turn the pulley and measure the backlash between the generator rotor and vacuum pump shaft.

Maximum backlash:

1.6 mm (0.0630 in.)


If the backlash is more than the maximum, replace the generator rotor and vacuum pump shaft.


Hide 29300 2.REMOVE VACUUM PUMP ASSEMBLY

a.
A220269E01
0.378,0.372 0.565,0.531 0.187,0.159 10 *a 1.47,0.719 0.677,0.471 0.677,0.471 0.596,0.471 false

Place matchmarks as shown in the illustration.

Text in Illustration
*a Matchmark


b.

Remove the 4 bolts and vacuum pump.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.
A220270

Remove the nut and terminal insulator.


b.

Remove the bolt, 3 nuts, rectifier plate and rear end cover.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.

Remove the brush holder cover.


b.
A226311

Remove the 2 screws and brush holder.


c.

Remove the plate seal.


Hide 27700A 5.REMOVE GENERATOR REGULATOR ASSEMBLY

a.
A226312

Remove the 3 screws and generator regulator.


Hide 27357 6.REMOVE GENERATOR HOLDER WITH RECTIFIER

a.
A220272

Remove the 4 screws and generator holder with rectifier.


b.

Remove the 4 rubber insulators.


Hide 27359 7.REMOVE GENERATOR RECTIFIER END FRAME

a.
A220273E01
3.052,1.028 3.236,1.181 0.183,0.153 10 *1 2.763,0.787 2.975,1.11 2.975,1.11 3.052,1.11 false

Remove the 4 nuts and cord clip.

Text in Illustration
*1 Cord Clip


b.
A220274E01
2.536,1.373 2.856,1.522 0.320,0.150 10 SST 0.57,0.359 0.737,0.507 0.167,0.148 10 *a 2.025,1.027 2.418,1.463 2.418,1.463 2.526,1.463 false

Using SST, remove the rectifier end frame.

SST
09286-46011  

Text in Illustration
*a Hold
V100135

Turn


c.

Remove the washer from the rotor.


Hide 27330 8.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A220275E01
2.224,0.147 2.532,0.307 0.308,0.160 10 SST 0.863,0.515 1.171,0.675 0.308,0.160 10 SST 1.856,0.56 2.1,0.231 2.1,0.231 2.206,0.231 false 1.685,0.945 1.316,0.602 1.316,0.602 1.229,0.602 false

Using SST and a press, press out the rotor.

SST
09950-60010  (09951-00180)
09950-70010  (09951-07100)