Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › GENERATOR
RM27T0E _57 Power Source / Network _053724 1GR-FE BATTERY / CHARGING _0261019 GENERATOR G

1GR-FE BATTERY / CHARGING  GENERATOR  INSPECTION  


PROCEDURE

Hide 27415 1.INSPECT GENERATOR WITH CLUTCH PULLEY

a.
A222451

Hold the center of the generator with clutch pulley and check that the outer ring turns counterclockwise and does not turn clockwise.

Text in Illustration
V100135

Free
V100136

Lock

If the result is not as specified, replace the generator with clutch pulley.


Hide 27370 2.INSPECT GENERATOR BRUSH HOLDER ASSEMBLY

a.
A128079E19
0.646,0.667 0.844,0.969 0.198,0.302 10 false *a

Using a vernier caliper, measure the brush length.

Standard exposed length:

9.5 to 11.5 mm (0.374 to 0.453 in.)


Minimum exposed length:

4.5 mm (0.177 in.)


Text in Illustration
*a Length

If the brush length is less than the minimum, replace the generator brush holder assembly.


Hide 27330 3.INSPECT GENERATOR ROTOR ASSEMBLY

a.
A079306

Check that the generator rotor bearing is not rough or worn.

If necessary, replace the generator rotor assembly.


b.

Check the generator rotor for an open circuit.

i.
B012264E55
0.365,1.156 0.365,0.167 0.365,0.167 0.917,0.167 true 0.948,0.073 1.115,0.229 0.167,0.156 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 100 A (w/o Dual Air Conditioning System), 130 A Type:
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 2.3 to 2.7 Ω

for 100 A (w/ Dual Air Conditioning System) Type:
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 3.4 to 3.8 Ω

for 150 A Type:
Tester Connection Condition Specified Condition
Slip ring - Slip ring 20°C (68°F) 1.5 to 1.9 Ω


Text in Illustration
*a Slip Ring

If the result is not as specified, replace the generator rotor assembly.



c.

Check if the generator rotor is grounded.

i.
B012265E48
0.354,1.115 0.354,0.156 0.354,0.156 0.646,0.156 true 1.135,0.802 1.365,0.271 1.365,0.271 1.51,0.271 true 0.677,0.063 0.865,0.24 0.188,0.177 10 false *a 1.531,0.177 1.719,0.354 0.188,0.177 10 false *b

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Slip ring - Rotor core Always 10 MΩ or higher


Text in Illustration
*a Slip Ring
*b Rotor Core

If the result is not as specified, replace the generator rotor assembly.



d.
A124106E09
0.667,0.542 0.844,0.688 0.177,0.146 10 false *a

Using a vernier caliper, measure the slip ring diameter.

Standard diameter:

14.2 to 14.8 mm (0.559 to 0.583 in.)


Minimum diameter:

14.0 mm (0.551 in.)


Text in Illustration
*a Diameter

If the diameter is less than the minimum, replace the generator rotor assembly.