Home › Power Source / Network › 1GR-FE (BATTERY / CHARGING) › GENERATOR
RM27T0E _57 Power Source / Network _053724 1GR-FE BATTERY / CHARGING _0261019 GENERATOR A

1GR-FE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A219663E02
1.01,1.063 0.635,0.5 0.635,0.5 0.427,0.5 true 0.948,1.198 0.5,0.5 true 0.146,0.417 0.458,0.594 0.313,0.177 10 false SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A219664E03
2.813,1.406 2.052,0.771 2.052,0.771 1.969,0.771 true 2.833,1.042 2.073,0.229 2.073,0.229 1.99,0.229 true 1.823,0.135 2.01,0.281 0.188,0.146 10 false *a 1.792,0.677 1.979,0.823 0.188,0.146 10 false *b

Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate.

Text in Illustration
*a Tab
*b Cutout


c.

Install the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Install the generator rotor to the drive end frame.


b.

Place the generator washer on the generator rotor.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A128082E12
1.615,0.615 1.052,0.417 false 0.885,0.281 1.063,0.604 0.177,0.323 10 false *a

Using a deep socket wrench (21 mm) and press, slowly press in the generator coil.

Text in Illustration
*a Deep Socket Wrench (21 mm)


b.

Install the 4 bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A079315E42
0.969,0.74 1.427,0.365 true 1.427,0.229 1.677,0.396 0.25,0.167 10 false *a

While pushing the 2 brushes into the generator brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.

Text in Illustration
*a Pin


b.
U169157E01
2.132,0.375 2.314,0.523 0.182,0.148 10 *a 1.931,0.631 2.035,0.451 2.035,0.451 2.127,0.451 false

Install the generator brush holder to the generator coil with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)

Text in Illustration
*a Pin


c.

Pull out the pin from the generator brush holder.


Hide 27387B 5.INSTALL GENERATOR TERMINAL INSULATOR

a.
A219668

Install the terminal insulator to the generator coil.

NOTICE:

Make sure the terminal insulator is installed facing the proper direction.



Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover to the generator coil with the 3 nuts.

Torque:
4.6 N*m (46 kgf*cm, 40 in.*lbf)


b.

Install the cord clip with the nut.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 27415 7.INSTALL GENERATOR WITH CLUTCH PULLEY

a.

Temporarily install the generator with clutch pulley by hand.


b.

Mount the generator in a vise between aluminum plates.


c.
A219555E05
1.198,0.906 1.323,0.24 1.323,0.24 1.458,0.24 false 1.323,1.188 1.406,1.75 1.406,1.75 1.531,1.75 false 2.115,0.792 2.229,0.385 2.229,0.385 2.375,0.385 true 3.073,1.156 2.885,1.521 2.885,1.521 2.76,1.521 false 2.406,0.302 2.604,0.479 0.198,0.177 10 false *1 1.563,1.667 2.104,1.823 0.542,0.156 10 false SST (A) 2.24,1.438 2.771,1.594 0.531,0.156 10 false SST (A) 1.49,0.167 2.042,0.323 0.552,0.156 10 false SST (B)

Install SST (A) and SST (B) to the generator with clutch pulley as shown in the illustration.

SST
09820-63021  

Text in Illustration
*1 Rotor Shaft

NOTICE:

Securely attach SST to the generator with clutch pulley and generator rotor shaft.



d.
A219557E05
1,0.656 0.771,0.115 0.771,0.115 0.677,0.115 false 0.646,0.938 0.302,1.042 0.302,1.042 0.302,1.125 false 0.115,1.135 0.677,1.313 0.563,0.177 10 false SST (A) 0.75,2.354 0.917,2.5 0.167,0.146 10 false *b 0.167,0.042 0.74,0.25 0.573,0.208 10 false SST (B) 1.24,2.104 1.417,2.26 0.177,0.156 10 false *a

Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator with clutch pulley.

Torque:
without SST : 80 N*m (816 kgf*cm, 59 ft.*lbf)
with SST : 64 N*m (653 kgf*cm, 47 ft.*lbf)

Text in Illustration
*a Fulcrum Length
*b Hold
V100135

Turn

HINT:
·

Use a torque wrench with a fulcrum length of 400 mm (15.7 in.). When using a torque wrench with a fulcrum length that is not 400 mm (15.7 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.



NOTICE:

Be careful as the generator with clutch pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



e.

Remove SST from the generator.


f.

Check that the generator with clutch pulley rotates smoothly.


Hide 27416 8.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the clutch pulley.