Home › Power Source / Network › 1KD-FTV (BATTERY / CHARGING) › GENERATOR › 2015.06–2020.08
RM27T0E _57 Power Source / Network _053726 1KD-FTV BATTERY / CHARGING _0261023 GENERATOR A

1KD-FTV BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27415 1.REMOVE GENERATOR WITH CLUTCH PULLEY

a.

Remove the generator pulley cap.


b.

Mount the generator in a vise between aluminum plates.


c.
A224863E02
2.698,1.448 2.427,1.448 2.427,1.448 1.885,1.094 false 2.896,0.75 2.427,1.448 false 1.375,1.667 1.302,1.667 1.302,1.667 1.063,1.344 false 2.729,1.354 3.26,1.531 0.531,0.177 10 false SST (A) 1.417,1.594 2.073,2.125 0.656,0.531 10 true SST (B)

Install SST (A) and (B) to the pulley as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley and generator rotor shaft.



d.
A224864E01
1.821,1.811 2.025,1.969 0.204,0.159 10 *a

Use a wrench to hold SST (A) and turn SST (B) counterclockwise to loosen the generator with clutch pulley.

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Be careful as the generator pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



e.

Remove SST from the generator.


f.

Remove the pulley.


Hide 27039 2.REMOVE GENERATOR REAR END COVER

a.
A079302

Remove the 3 nuts and generator rear end cover.


Hide 27387 3.REMOVE TERMINAL INSULATOR

a.
A079342

Remove the terminal insulator.


Hide 27370 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A079303

Remove the 2 screws and generator brush holder assembly.


Hide 27360 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A079304

Remove the 4 through bolts.


b.
U169079E01
0.225,0.711 0.396,0.885 0.170,0.174 10 *a

Using SST, remove the generator coil.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)

Text in Illustration
*a Hold
V100135

Turn


c.

Remove the generator washer.


Hide 27330 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.

Remove the generator rotor from the drive end frame.


Hide 27310B 7.CHECK GENERATOR DRIVE END FRAME BEARING

a.
A079307

Check that the bearing is not rough or worn.

If necessary, replace the generator drive end frame bearing.


Hide 27310B 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A079311

Remove the 4 screws and bearing retainer.


b.
A115881E01
0.212,1.004 0.517,1.153 0.305,0.149 10 SST 1.186,1.094 0.57,1.094 0.57,1.094 1.124,1.345 false

Using SST, tap out the bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)