Home › Power Source / Network › 1KD-FTV (BATTERY / CHARGING) › GENERATOR › 2015.06–2020.08
RM27T0E _57 Power Source / Network _053726 1KD-FTV BATTERY / CHARGING _0261023 GENERATOR A

1KD-FTV BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A102672E01
2.875,0.207 3.179,0.359 0.304,0.151 10 SST 1.809,0.972 2.505,0.285 2.505,0.285 2.795,0.285 false 1.871,1.204 2.505,0.285 false

Using SST and a press, press in a new bearing.

SST
09950-60010  (09951-00520)
09950-70010  (09951-07100)


b.
A079311E02
0.354,0.73 0.542,0.869 0.189,0.139 10 *1 0.602,0.805 0.693,0.805 0.693,0.805 1.495,1.16 false 2.846,1.536 3.034,1.675 0.189,0.139 10 *1 2.726,1.633 2.652,1.633 2.652,1.633 1.999,1.381 false

Align the claws of the bearing retainer with the grooves inside the generator drive end frame.

Text in Illustration
*1 Claw


c.

Install the bearing retainer with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Install the rotor and washer to the drive end frame.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A158387E03
1.542,0.656 2.052,0.281 2.052,0.281 2.198,0.281 true 2.24,0.177 2.427,0.344 0.188,0.167 10 false *1

Using a deep socket wrench (21 mm) and press, slowly press on the generator coil.

Text in Illustration
*1 Deep Socket Wrench (21 mm)


b.
A079304

Install the generator coil with the 4 through bolts.

Torque:
5.8 N*m (59 kgf*cm, 51 in.*lbf)


Hide 27370 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A113845E06
1.37,0.253 1.598,0.400 0.228,0.147 10 *1 0.991,0.533 1.215,0.343 1.215,0.343 1.308,0.34 false

While pushing the 2 brushes into the generator brush holder, insert a φ1.0 mm (0.0394 in.) pin into the generator brush holder hole.

Text in Illustration
*1 Pin


b.
A079303E05
0.448,1.604 1.656,1.271 true 0.271,1.542 0.5,1.688 0.229,0.146 10 false *1

Install the brush holder with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the brush holder.

Text in Illustration
*1 Pin


Hide 27387 5.INSTALL TERMINAL INSULATOR

A079318

Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover with the 3 nuts.

Torque:
4.6 N*m (46 kgf*cm, 40 in.*lbf)


Hide 27415 7.INSTALL GENERATOR WITH CLUTCH PULLEY

a.

Install the pulley by hand.


b.

Mount generator in a vise between aluminum plates.


c.
A224863E03
2.698,1.448 2.427,1.448 2.427,1.448 1.885,1.094 false 2.896,0.75 2.427,1.448 false 1.375,1.677 1.302,1.677 1.302,1.677 1.063,1.354 false 2.74,1.354 3.271,1.531 0.531,0.177 10 false SST (A) 1.427,1.604 2.094,2.135 0.667,0.531 10 true SST (B)

Install SST (A) and (B) to the generator with clutch pulley as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator with clutch pulley and generator rotor shaft.



d.
A224865E02
2.25,1.146 2.604,1.198 false 1.906,0.958 2.135,0.469 2.135,0.469 2.302,0.469 true 1.958,2.125 2.135,2.281 0.177,0.156 10 false *a 1.563,1.927 1.719,2.094 0.156,0.167 10 true *1 2.333,0.385 2.958,0.594 0.625,0.208 10 false SST (B) 2.635,1.125 3.26,1.333 0.625,0.208 10 false SST (A)

Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator pulley with clutch.

Torque:
without SST : 111 N*m (1127 kgf*cm, 81 ft.*lbf)
with SST : 83 N*m (844 kgf*cm, 61 ft.*lbf)

Text in Illustration
*1 Fulcrum Length
*a Hold
V100135

Turn

HINT:
·

Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.



NOTICE:

Be careful as the generator with clutch pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.



e.

Remove SST from the generator.


f.

Check that the generator pulley rotates smoothly.


g.

Install a new generator pulley cap.