Home › Power Source / Network › 1GD-FTV (BATTERY / CHARGING) › GENERATOR (for 130 A Type)
RM27T0E _57 Power Source / Network _053727 1GD-FTV BATTERY / CHARGING _0261027 GENERATOR(for 130 A Type) A

1GD-FTV BATTERY / CHARGING  GENERATOR(for 130 A Type)  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A341818E01
2.233,0.864 1.793,0.222 1.793,0.222 2.372,0.417 false 1.433,0.113 1.806,0.292 0.373,0.179 10 SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A341820E02
2.625,0.906 1.938,0.25 1.938,0.25 1.844,0.25 true 2.594,1.302 1.792,1.302 1.792,1.302 1.781,1.917 true 1.677,0.135 1.906,0.333 0.229,0.198 10 false *a 1.708,1.927 1.917,2.125 0.208,0.198 10 false *b

Fit the tabs on the retainer plate into the cutouts on the drive end frame to install the retainer plate.

Text in Illustration
*a Tab
*b Cutout


c.

Install the retainer plate with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame on the generator pulley with clutch.


b.

Install the generator rotor assembly to the generator drive end frame.


Hide 27444 3.INSTALL GENERATOR BEARING COVER PACKING

NOTICE:

A new generator coil assembly comes with a generator bearing cover packing. Therefore, it is not necessary to install a new generator bearing cover packing when installing a new generator coil assembly.


a.
A314531E07
1.938,0.49 2.406,0.49 true 1.958,1.417 2.448,1.417 true 2.417,0.385 2.625,0.552 0.208,0.167 10 false *a 2.448,1.313 2.656,1.479 0.208,0.167 10 false *b

Install a new generator bearing cover packing to the generator coil assembly.

Text in Illustration
*a Protrusion
*b Groove

NOTICE:

Align the protrusion of the generator bearing cover packing with the groove of the generator coil assembly when installing.



Hide 27360 4.INSTALL GENERATOR COIL ASSEMBLY

a.
A351793E01
1.231,0.659 0.805,0.226 0.805,0.226 0.693,0.226 false 2.531,0.531 2.09,0.205 2.09,0.205 1.987,0.205 false 0.479,0.123 0.683,0.300 0.205,0.177 10 *a 1.798,0.097 2.002,0.274 0.205,0.177 10 *a

Using a 21 mm deep socket wrench and press, slowly press on the generator coil assembly.

Text in Illustration
*a 21 mm Deep Socket Wrench


b.

Install the generator coil assembly with the 4 through bolts.

Torque:
5.6 N*m (57 kgf*cm, 50 in.*lbf)


Hide 27370 5.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A079315E43
0.958,0.771 1.458,0.448 true 1.469,0.302 1.719,0.469 0.25,0.167 10 false *a

While pushing the 2 brushes into the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.

Text in Illustration
*a Pin


b.
A351794E02
1.688,0.948 0.635,1.833 0.635,1.833 0.521,1.833 true 0.354,1.74 0.583,1.927 0.229,0.188 10 false *a

Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)

Text in Illustration
*a Pin


c.

Pull out the pin from the generator brush holder assembly.


Hide 27387 6.INSTALL TERMINAL INSULATOR

a.
A351795

Install the terminal insulator to the generator coil assembly.

NOTICE:

Make sure that the terminal insulator is installed with the correct orientation.



Hide 27039 7.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 8.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Mount the generator assembly in the vise between aluminum plates.


b.

Temporarily install the generator pulley with clutch by hand.


c.
A351796E02
0.406,0.635 1.76,0.219 1.76,0.219 1.667,0.948 true 2.375,1.135 1.521,1.927 1.521,1.927 1.438,1.927 true 1.156,0.698 1.156,1.458 true 1.813,0.115 2.302,0.313 0.49,0.198 10 false SST A 1,1.844 1.49,2.042 0.49,0.198 10 false SST B 1.083,1.458 1.292,1.625 0.208,0.167 10 false *a

Install SST A and SST B to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

Text in Illustration
*a Generator Rotor Shaft

NOTICE:

Securely attach SST to the generator pulley with clutch and generator rotor shaft.



d.
A351798E02
0.833,1.281 0.74,0.958 0.74,0.958 0.635,0.958 false 1.115,1.146 0.938,0.583 0.938,0.583 0.833,0.583 false 0.188,0.875 0.646,1.042 0.458,0.167 10 false SST A 0.406,0.49 0.865,0.656 0.458,0.167 10 false SST B 1,2.729 1.24,2.917 0.24,0.188 10 false *a 1.375,4.188 1.615,4.375 0.24,0.188 10 false *c 1.823,2.406 2.063,2.594 0.24,0.188 10 false *b

Using a wrench to hold SST A, turn SST B clockwise to tighten the generator pulley with clutch.

Torque:
Specified tightening torque : 110.5 N*m (1127 kgf*cm, 81 ft.*lbf)

Text in Illustration
*a Hold
*b Torque Wrench Fulcrum Length
*c SST Fulcrum Length
V100135

Turn

NOTICE:

Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

(See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (15.8 in.)):

88.4 N*m (901 kgf*cm, 65 ft.*lbf)




e.

Remove SST from the generator assembly.


f.

Check that the generator pulley with clutch rotates smoothly.


g.

Remove the generator assembly from the vise.


Hide 27416 9.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the generator pulley with clutch.