Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0100 There is no communication from the ECM.
·

Power source or inside ECM

·

ECM main wire or connector

·

ECM



WIRING DIAGRAM

C348084E01
0.115,0.073 4,0.385 3.885,0.313 12 false for 1GR-FE and Manual Transmission System: 0.406,1.865 4.073,2.063 3.667,0.198 10 false No. 1 Junction Connector 0.396,1.708 1.677,1.906 1.281,0.198 10 false G98 1.813,0.969 2.031,1.167 0.219,0.198 10 false 9 1.813,1.313 2.031,1.51 0.219,0.198 10 false 20 5.833,1.448 6.448,1.646 0.615,0.198 10 false CANN 5.833,1.083 6.448,1.281 0.615,0.198 10 false CANP 5.833,1.823 6.448,2.021 0.615,0.198 10 false BATT 5.833,2.198 6.448,2.396 0.615,0.198 10 false +B 5.833,2.573 6.448,2.771 0.615,0.198 10 false +B2 5.833,2.927 6.448,3.125 0.615,0.198 10 false MREL 5.833,3.271 6.448,3.469 0.615,0.198 10 false EC 5.833,3.635 6.448,3.833 0.615,0.198 10 false ME01 5.833,3.969 6.448,4.167 0.615,0.198 10 false E02 5.833,4.333 6.448,4.531 0.615,0.198 10 false E1 5.833,4.719 6.448,4.917 0.615,0.198 10 false E01 6,5.135 6.615,5.333 0.615,0.198 10 false ECM 5.458,1.104 5.917,1.302 0.458,0.198 10 false G56 5.458,1.448 5.917,1.646 0.458,0.198 10 false G56 5.469,1.833 5.927,2.031 0.458,0.198 10 false G55 5.458,3.281 5.917,3.479 0.458,0.198 10 false G55 5.479,2.927 5.938,3.125 0.458,0.198 10 false G55 5.469,2.563 5.927,2.76 0.458,0.198 10 false G55 5.469,2.198 5.927,2.396 0.458,0.198 10 false G55 5.469,3.646 5.927,3.844 0.458,0.198 10 false C37 5.479,4 5.938,4.198 0.458,0.198 10 false C37 5.469,4.354 5.927,4.552 0.458,0.198 10 false C36 5.469,4.708 5.927,4.906 0.458,0.198 10 false C37 5.51,0.906 5.969,1.104 0.458,0.198 10 false 34 5.521,1.292 5.979,1.49 0.458,0.198 10 false 33 5.521,1.656 5.979,1.854 0.458,0.198 10 false 24 5.521,2.01 5.979,2.208 0.458,0.198 10 false 22 5.521,2.375 5.979,2.573 0.458,0.198 10 false 23 5.542,2.76 6,2.958 0.458,0.198 10 false 9 5.5,3.094 5.958,3.292 0.458,0.198 10 false 12 5.5,3.469 5.958,3.667 0.458,0.198 10 false 10 5.51,3.823 5.969,4.021 0.458,0.198 10 false 15 5.51,4.167 5.969,4.365 0.458,0.198 10 false 12 5.5,4.531 5.958,4.729 0.458,0.198 10 false 14 4.896,1.656 5.51,1.854 0.615,0.198 10 false EFI 3.469,1.823 4.667,2.167 1.198,0.344 10 false from Battery 3.333,2.167 4.531,2.51 1.198,0.344 10 false from EFI Relay 3.469,2.896 4.667,3.24 1.198,0.344 10 false to EFI Relay

C348085E01
0.125,0.083 2.333,0.323 2.208,0.24 12 false for 1KD-FTV: 0.385,1.865 2.219,2.094 1.833,0.229 10 false No. 1 Junction Connector 0.385,1.719 2.219,1.948 1.833,0.229 10 false G98 1.792,0.958 2.083,1.167 0.292,0.208 10 false 9 1.792,1.313 2.083,1.521 0.292,0.208 10 false 20 5.833,1.094 6.448,1.292 0.615,0.198 10 false CANP 5.833,1.448 6.448,1.646 0.615,0.198 10 false CANN 5.833,1.833 6.448,2.031 0.615,0.198 10 false BATT 5.833,2.198 6.448,2.396 0.615,0.198 10 false +B 5.833,2.583 6.448,2.781 0.615,0.198 10 false +B2 5.833,2.917 6.448,3.115 0.615,0.198 10 false MREL 5.833,3.292 6.448,3.49 0.615,0.198 10 false EC 5.833,3.635 6.448,3.833 0.615,0.198 10 false ME01 5.833,3.979 6.448,4.177 0.615,0.198 10 false E1 5.823,4.354 6.438,4.552 0.615,0.198 10 false E02 5.833,4.698 6.448,4.896 0.615,0.198 10 false E01 5.99,5.115 6.604,5.313 0.615,0.198 10 false ECM 5.479,1.104 5.938,1.302 0.458,0.198 10 false G57 5.469,1.448 5.927,1.646 0.458,0.198 10 false G57 5.469,1.854 5.927,2.052 0.458,0.198 10 false G57 5.469,2.583 5.927,2.781 0.458,0.198 10 false G57 5.469,2.198 5.927,2.396 0.458,0.198 10 false G57 5.458,3.292 5.917,3.49 0.458,0.198 10 false G57 5.448,2.927 5.906,3.125 0.458,0.198 10 false G58 5.469,3.646 5.927,3.844 0.458,0.198 10 false C93 5.458,4.01 5.917,4.208 0.458,0.198 10 false C93 5.458,4.354 5.917,4.552 0.458,0.198 10 false C93 5.458,4.708 5.917,4.906 0.458,0.198 10 false C93 5.49,0.917 5.948,1.115 0.458,0.198 10 false 20 5.51,1.281 5.969,1.479 0.458,0.198 10 false 21 5.521,1.656 5.979,1.854 0.458,0.198 10 false 23 5.51,2.021 5.969,2.219 0.458,0.198 10 false 24 5.521,2.385 5.979,2.583 0.458,0.198 10 false 17 5.521,2.74 5.979,2.938 0.458,0.198 10 false 11 5.5,3.115 5.958,3.313 0.458,0.198 10 false 11 5.542,3.458 6,3.656 0.458,0.198 10 false 8 5.552,3.813 6.01,4.01 0.458,0.198 10 false 1 5.521,4.177 5.979,4.375 0.458,0.198 10 false 13 5.51,4.531 5.969,4.729 0.458,0.198 10 false 12 4.885,1.688 5.5,1.885 0.615,0.198 10 false EFI 3.479,1.813 4.625,2.042 1.146,0.229 10 false from Battery 3.323,2.177 4.469,2.406 1.146,0.229 10 false from EFI Relay 3.469,2.896 4.615,3.125 1.146,0.229 10 false to EFI Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM MAIN WIRE)
2.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM MAIN WIRE)
a.

Disconnect the G56*1 or G57*2 ECM connector.

*1: for 1GR-FE and Manual Transmission System

*2: for 1KD-FTV


U170207E01
2.094,0.255 2.387,0.420 0.293,0.164 10 G56 2.533,0.255 2.825,0.420 0.293,0.164 10 *A 0.176,0.107 0.373,0.287 0.197,0.180 10 *a 1.631,2.537 2.236,2.695 0.605,0.159 10 CANP*A 1.064,2.343 1.666,2.500 0.602,0.158 10 CANN*A 2.139,2.075 1.712,2.406 1.712,2.406 1.632,2.406 false 2.37,2.066 2.271,2.604 2.271,2.604 2.19,2.604 false 3.746,2.273 4.351,2.432 0.605,0.159 10 CANP*B 5.054,2.324 5.656,2.482 0.602,0.158 10 CANN*B 4.625,1.844 4.419,2.331 4.419,2.331 4.338,2.331 false 4.712,1.844 4.951,2.395 4.951,2.395 5.032,2.395 false 4.896,0.379 5.189,0.543 0.293,0.164 10 G57 5.335,0.379 5.627,0.543 0.293,0.164 10 *B


Text in Illustration
*A for 1GR-FE and Manual Transmission System *B for 1KD-FTV
*a Front view of wire harness connector
(to ECM)
- -

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE and Manual Transmission System
Tester Connection Switch Condition Specified Condition
G56-34 (CANP) - G56-33 (CANN) Engine switch off 108 to 132 Ω

for 1KD-FTV
Tester Connection Switch Condition Specified Condition
G57-20 (CANP) - G57-21 (CANN) Engine switch off 108 to 132 Ω




OK

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ECM MAIN WIRE OR CONNECTOR (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

for 1GR-FE and Manual Transmission System:

i.

Disconnect the C36, C37 and G55 ECM connectors.

U148698E01
0.144,0.712 0.437,0.876 0.293,0.164 10 C36 2.47,0.726 2.763,0.890 0.293,0.164 10 C37 4.975,0.726 5.267,0.890 0.293,0.164 10 G55 4.452,0.682 4.842,0.846 0.390,0.164 10 ME01 0.338,1.389 0.535,1.553 0.197,0.164 10 E1 0.04,0.006 0.237,0.171 0.197,0.164 10 *a 0.804,0.912 0.622,1.462 0.622,1.462 0.525,1.462 false 4.792,0.098 5.207,0.262 0.415,0.164 10 MREL 5.667,0.848 5.295,0.172 5.295,0.172 5.198,0.172 false 4.149,0.872 4.344,0.754 4.344,0.754 4.44,0.754 false 6.792,0.63 7.029,0.794 0.237,0.164 10 EC 6.489,0.821 6.684,0.702 6.684,0.702 6.781,0.702 false 6.703,1.263 7.096,1.427 0.393,0.164 10 BATT 6.4,1.252 6.595,1.335 6.595,1.335 6.691,1.335 false 6.477,1.462 6.870,1.626 0.393,0.164 10 +B2 6.157,1.255 6.369,1.534 6.369,1.534 6.466,1.534 false 6.136,1.581 6.417,1.745 0.281,0.164 10 +B 5.892,1.255 6.027,1.653 6.027,1.653 6.124,1.653 false 4.242,1.462 4.520,1.626 0.278,0.164 10 E01 3.869,1.071 4.134,1.534 4.134,1.534 4.23,1.534 false 4.488,1.228 4.766,1.392 0.278,0.164 10 E02 4.102,1.077 4.379,1.3 4.379,1.3 4.476,1.3 false

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-12 (E1) - Body ground Always Below 1 Ω
C37-14 (E01) - Body ground Always Below 1 Ω
C37-15 (E02) - Body ground Always Below 1 Ω
C37-10 (ME01) - Body ground Always Below 1 Ω
G55-12 (EC) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G55-24 (BATT) - Body ground Always 11 to 14 V
G55-23 (+B2) - Body ground Battery positive (+) voltage applied to terminal G55-9 (MREL) 11 to 14 V
G55-22 (+B) - Body ground Battery positive (+) voltage applied to terminal G55-9 (MREL) 11 to 14 V




b.

for 1KD-FTV:

i.

Disconnect the C93, G57 and G58 ECM connectors.

U170372E01
0.094,0.076 0.365,0.323 0.270,0.246 10 *a 0.284,0.838 0.558,0.979 0.274,0.141 10 C93 2.774,0.838 3.055,0.979 0.281,0.141 10 G57 5.091,0.838 5.372,0.979 0.281,0.141 10 G58 0.872,0.7 0.661,0.49 0.661,0.49 0.553,0.49 false 0.619,1.537 0.732,1.537 0.732,1.537 1.117,1.141 false 1.377,1.141 1.677,1.663 1.677,1.663 1.817,1.663 false 1.39,0.871 1.849,0.409 1.849,0.409 2.059,0.409 false 3.916,0.85 4.285,0.518 4.285,0.518 4.423,0.518 false 4.549,0.892 4.427,0.892 4.427,0.892 4.217,1.026 false 3.916,1.313 4.108,1.688 4.108,1.688 4.199,1.688 false 6.608,0.675 6.485,0.675 6.485,0.675 6.289,0.812 false 4.474,1.49 4.348,1.49 4.348,1.49 4.147,1.313 false 6.637,0.616 7.064,0.758 0.427,0.142 10 MREL 4.441,0.458 4.868,0.600 0.427,0.142 10 EC 4.563,0.829 4.990,0.971 0.427,0.142 10 +B2 4.493,1.414 4.920,1.556 0.427,0.142 10 +B 4.217,1.614 4.643,1.756 0.427,0.142 10 BATT 2.075,0.344 2.502,0.486 0.427,0.142 10 ME01 1.837,1.605 2.263,1.747 0.427,0.142 10 E02 0.348,1.474 0.775,1.616 0.427,0.142 10 E01 0.348,0.416 0.775,0.558 0.427,0.142 10 E1

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C93-1 (E1) - Body ground Always Below 1 Ω
C93-12 (E01) - Body ground Always Below 1 Ω
C93-13 (E02) - Body ground Always Below 1 Ω
C93-8 (ME01) - Body ground Always Below 1 Ω
G57-11 (EC) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G57-23 (BATT) - Body ground Always 11 to 14 V
G57-17 (+B2) - Body ground Battery positive (+) voltage applied to terminal G58-11 (MREL) 11 to 14 V
G57-24 (+B) - Body ground Battery positive (+) voltage applied to terminal G58-11 (MREL) 11 to 14 V




Result
Result Proceed to
OK (for 1GR-FE) A
OK (for 1KD-FTV) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR