Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  U0182  Lost Communication with AFS ECU  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0182 There is no communication from the headlight swivel ECU assembly.
·

Power source or inside headlight swivel ECU assembly

·

Headlight swivel ECU assembly branch wire or connector

·

Headlight swivel ECU assembly



For vehicles with a LED headlight.


WIRING DIAGRAM

C217350E63
5.625,2.771 6.021,2.948 0.396,0.177 10 false A58 5.625,2.927 6.99,3.313 1.365,0.385 10 false Headlight Swivel ECU Assembly 0.656,1.583 2.313,1.76 1.656,0.177 10 false No. 4 Junction Connector 5.813,0.594 6.281,0.771 0.469,0.177 10 false CANH 0.646,1.438 0.958,1.615 0.313,0.177 10 false A73 1.938,0.51 2.042,0.667 0.104,0.156 10 false 4 5.531,0.49 5.74,0.667 0.208,0.177 10 false 12 5.542,0.917 5.75,1.094 0.208,0.177 10 false 13 5.531,1.813 5.74,1.99 0.208,0.177 10 false 15 5.542,2.198 5.74,2.354 0.198,0.156 10 false 22 4.396,1.76 5.333,1.917 0.938,0.156 10 false ECU-IG NO. 1 2.302,1.927 3.677,2.104 1.375,0.177 10 false from IG1 NO. 1 Relay 1.917,0.948 2.115,1.104 0.198,0.156 10 false 15 5.813,1.052 6.281,1.229 0.469,0.177 10 false CANL 5.813,1.958 6.281,2.135 0.469,0.177 10 false IG 5.823,2.323 6.292,2.5 0.469,0.177 10 false E1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY CAN BRANCH WIRE)
a.
U170208E03
2.385,1.823 2.49,1.823 2.49,1.823 2.74,1.115 true 2.813,0.469 2.708,0.469 2.708,0.469 2.615,1.031 true 1.552,0.281 1.833,0.479 0.281,0.198 10 false A58 2.865,0.396 3.323,0.583 0.458,0.188 10 false CANH 1.979,1.74 2.448,1.896 0.469,0.156 10 false CANL 0.104,0.063 0.354,0.292 0.25,0.229 10 false *a

Disconnect the A58 headlight swivel ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A58-12 (CANH) - A58-13 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170209E03
1.833,1.688 1.688,1.688 1.688,1.688 1.552,1.25 true 0.417,1.635 0.531,1.635 0.531,1.635 0.719,1.24 true 1.552,0.25 1.833,0.448 0.281,0.198 10 false A58 0.219,1.563 0.417,1.719 0.198,0.156 10 false IG 1.865,1.625 2.354,1.771 0.49,0.146 10 false E1 0.104,0.073 0.354,0.302 0.25,0.229 10 false *a

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-22 (E1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A58-15 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly)


OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR