Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  U0139  Lost Communication with Suspension Control Module B  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0139 There is no communication from the stabilizer control ECU.
·

Power source or inside stabilizer control ECU

·

Stabilizer control ECU CAN branch wire or connector

·

Stabilizer control ECU



For vehicles with a kinetic dynamic suspension system.


WIRING DIAGRAM

C348086E01
0.51,1.448 2.219,1.719 1.708,0.271 10 false No. 3 Junction Connector 0.51,1.302 2.219,1.573 1.708,0.271 10 false G95 1.958,0.49 2.375,0.667 0.417,0.177 10 false 5 1.958,0.896 2.375,1.073 0.417,0.177 10 false 16 5.479,0.469 5.896,0.646 0.417,0.177 10 false 29 5.479,0.906 5.896,1.083 0.417,0.177 10 false 28 5.5,1.625 5.917,1.802 0.417,0.177 10 false 24 5.49,2.219 5.906,2.396 0.417,0.177 10 false 22 5.833,0.604 6.469,0.854 0.635,0.25 10 false CANH 5.833,1.042 6.469,1.292 0.635,0.25 10 false CANL 5.844,1.76 6.479,2.01 0.635,0.25 10 false IG 5.844,2.344 6.479,2.594 0.635,0.25 10 false GND 5.396,2.823 7.104,3.094 1.708,0.271 10 false Stabilizer Control ECU 5.385,2.677 7.094,2.948 1.708,0.271 10 false G123 4.656,1.604 5.292,1.854 0.635,0.25 10 false KDSS 2.323,1.729 4.031,2 1.708,0.271 10 false from IG1 NO. 3 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (STABILIZER CONTROL ECU CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (STABILIZER CONTROL ECU CAN BRANCH WIRE)
a.
U148444E03
1.208,1.573 0.823,1.24 0.823,1.24 0.729,1.24 true 1.292,1.615 0.896,1.927 0.896,1.927 0.813,1.927 true 0.302,1.167 0.729,1.313 0.427,0.146 10 false CANH 0.427,1.844 0.854,1.99 0.427,0.146 10 false CANL 0.115,0.031 0.542,0.177 0.427,0.146 10 false *a 0.24,1.469 0.615,1.615 0.375,0.146 10 false G123

Disconnect the G123 stabilizer control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G123-29 (CANH) - G123-28 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Stabilizer Control ECU)



OK

3.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - BATTERY AND GROUND)

NG

REPAIR OR REPLACE STABILIZER CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - BATTERY AND GROUND)
a.
U148445E02
1.802,1.615 2.24,1.99 2.24,1.99 2.313,1.99 true 1.635,1.615 1.229,2.021 1.229,2.021 1.146,2.021 true 2.344,1.927 2.698,2.073 0.354,0.146 10 false GND 0.958,1.948 1.125,2.094 0.167,0.146 10 false IG 0.115,0.031 0.542,0.177 0.427,0.146 10 false *a 0.219,1.385 0.594,1.531 0.375,0.146 10 false G123

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-22 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G123-24 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Stabilizer Control ECU)


OK

REPLACE STABILIZER CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR