Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261032 CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on "Bus Check".

·

"Skid Control ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside master cylinder solenoid (skid control ECU)

·

Master cylinder solenoid (skid control ECU) branch wire or connector

·

Master cylinder solenoid (skid control ECU)



For vehicles with a 1KD-FTV engine.


WIRING DIAGRAM

C217310E19
5.823,1.125 6.208,1.281 0.385,0.156 10 false +BM1 5.823,1.479 6.24,1.635 0.417,0.156 10 false +BM2 5.823,2.573 6.25,2.74 0.427,0.167 10 false GND1 5.823,3.313 6.25,3.479 0.427,0.167 10 false GND3 4.521,0.99 5.25,1.156 0.729,0.167 10 false ABS NO.1 4.521,1.74 5.25,1.906 0.729,0.167 10 false ABS NO.2 4.667,2.094 4.958,2.25 0.292,0.156 10 false IGN 2.948,1.115 3.76,1.323 0.813,0.208 10 false from Battery 0.51,1.031 1.063,1.208 0.552,0.177 10 false A73 1.76,0.292 1.958,0.469 0.198,0.177 10 false 11 1.76,0.635 1.958,0.813 0.198,0.177 10 false 22 0.51,1.177 2.135,1.375 1.625,0.198 10 false No. 5 Junction Connector 2.792,2.208 3.781,2.438 0.99,0.229 10 false from IG2 Relay 5.51,1.125 5.771,1.292 0.26,0.167 10 false A7 5.51,1.49 5.771,1.656 0.26,0.167 10 false A8 5.51,2.583 5.771,2.729 0.26,0.146 10 false A7 5.51,3.292 5.771,3.448 0.26,0.156 10 false A8 5.573,0.948 5.677,1.104 0.104,0.156 10 false 2 5.823,2.229 6.094,2.385 0.271,0.156 10 false IG2 5.51,2.229 5.771,2.385 0.26,0.156 10 false A8 5.563,2.042 5.677,2.198 0.115,0.156 10 false 1 5.573,1.302 5.688,1.469 0.115,0.167 10 false 2 5.823,1.854 6.135,2.01 0.313,0.156 10 false +BS 5.51,1.865 5.771,2.031 0.26,0.167 10 false A7 5.531,1.677 5.708,1.844 0.177,0.167 10 false 31 5.823,0.396 6.25,0.542 0.427,0.146 10 false CANH 5.823,0.75 6.219,0.917 0.396,0.167 10 false CANL 5.51,0.396 5.76,0.552 0.25,0.156 10 false A7 5.51,0.74 5.771,0.896 0.26,0.156 10 false A7 5.51,0.208 5.708,0.365 0.198,0.156 10 false 11 5.51,0.563 5.708,0.729 0.198,0.167 10 false 25 5.563,2.385 5.667,2.552 0.104,0.167 10 false 1 5.823,2.938 6.24,3.104 0.417,0.167 10 false GND2 5.51,2.927 5.771,3.083 0.26,0.156 10 false A7 5.531,2.75 5.74,2.927 0.208,0.177 10 false 32 5.563,3.115 5.667,3.271 0.104,0.156 10 false 4 5.375,3.823 7.01,4.208 1.635,0.385 10 false Master Cylinder Solenoid (Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)
a.
U115863E01
0.073,0.08 0.270,0.266 0.197,0.186 10 *a 1.595,0.663 1.881,0.849 0.286,0.186 10 A7 2.493,0.813 2.933,0.999 0.440,0.186 10 CANH 2.864,1.077 3.262,1.246 0.398,0.169 10 CANL 2.207,1.77 2.36,0.902 2.36,0.902 2.465,0.902 false 2.207,1.896 2.765,1.162 2.765,1.162 2.843,1.162 false

Disconnect the A7 master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A7-11 (CANH) - A7-25 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SKID CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U148344E05
1.01,0.385 0.885,0.385 0.885,0.385 0.76,1.302 false 1.417,0.656 1.292,0.656 1.292,0.656 1.052,1.302 false 2.198,2.823 2.083,2.823 2.083,2.823 1.875,3.375 false 0.99,2.604 0.875,2.604 0.875,2.604 0.75,1.688 false 1.063,2.938 1.177,2.938 1.177,2.938 1.573,3.406 false 1.385,2.365 1.281,2.365 1.281,2.365 1.042,1.698 false 2.365,4.104 2.26,4.104 2.26,4.104 1.938,3.74 false 0.031,0.042 0.313,0.271 0.281,0.229 10 false *a 1.042,0.302 1.458,0.479 0.417,0.177 10 false GND1 1.031,2.521 1.333,2.698 0.302,0.177 10 false +BS 0.792,2.854 1.063,3.031 0.271,0.177 10 false IG2 0.698,3.49 0.969,3.667 0.271,0.177 10 false A8 1.458,0.573 1.865,0.75 0.406,0.177 10 false +BM1 2.229,2.729 2.635,2.906 0.406,0.177 10 false +BM2 1.417,2.292 1.823,2.469 0.406,0.177 10 false GND2 2.406,4.021 2.813,4.198 0.406,0.177 10 false GND3 1.833,0.281 2.104,0.458 0.271,0.177 10 false A7

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the A8 master cylinder solenoid (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-1 (GND1) - Body ground Always Below 1 Ω
A7-32 (GND2) - Body ground Always Below 1 Ω
A8-4 (GND3) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-2 (+BM1) - Body ground Always 11 to 14 V
A8-2 (+BM2) - Body ground Always 11 to 14 V
A7-31 (+BS) - Body ground Always 11 to 14 V
A8-1 (IG2) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])


OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR