Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261032 CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on "Bus Check".

·

"ECM Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside ECM

·

ECM



WIRING DIAGRAM

E346820E01
0.094,0.063 1.292,0.313 1.198,0.25 12 false for 1KD-FTV: 1.823,0.396 3.021,0.646 1.198,0.25 10 false from Battery 1.667,0.74 2.865,0.99 1.198,0.25 10 false from EFI Relay 1.813,1.49 3.01,1.74 1.198,0.25 10 false to EFI Relay 3.448,0.26 4.646,0.51 1.198,0.25 10 false EFI 5.469,0.417 5.948,0.594 0.479,0.177 10 false G57 5.542,0.24 6.021,0.417 0.479,0.177 10 false 23 5.792,0.406 6.271,0.583 0.479,0.177 10 false BATT 5.458,0.771 5.938,0.948 0.479,0.177 10 false G57 5.521,0.594 6,0.771 0.479,0.177 10 false 24 5.802,0.75 6.281,0.927 0.479,0.177 10 false +B 5.458,1.156 5.938,1.333 0.479,0.177 10 false G57 5.521,0.979 6,1.156 0.479,0.177 10 false 17 5.802,1.156 6.281,1.333 0.479,0.177 10 false +B2 5.469,1.51 5.948,1.688 0.479,0.177 10 false G58 5.521,1.333 6,1.51 0.479,0.177 10 false 11 5.781,1.51 6.26,1.688 0.479,0.177 10 false MREL 5.458,1.854 5.938,2.031 0.479,0.177 10 false G57 5.479,2.208 5.958,2.385 0.479,0.177 10 false C93 5.469,2.563 5.948,2.74 0.479,0.177 10 false C93 5.479,2.927 5.958,3.104 0.479,0.177 10 false C93 5.479,3.281 5.958,3.458 0.479,0.177 10 false C93 5.781,1.854 6.26,2.031 0.479,0.177 10 false EC 5.781,2.208 6.26,2.385 0.479,0.177 10 false ME01 5.792,2.563 6.271,2.74 0.479,0.177 10 false E1 5.802,2.917 6.281,3.094 0.479,0.177 10 false E02 5.792,3.281 6.271,3.458 0.479,0.177 10 false E01 6.042,3.604 6.521,3.781 0.479,0.177 10 false ECM 5.521,1.688 6,1.865 0.479,0.177 10 false 11 5.552,2.042 6.031,2.219 0.479,0.177 10 false 8 5.552,2.385 6.031,2.563 0.479,0.177 10 false 1 5.51,2.74 5.99,2.917 0.479,0.177 10 false 13 5.521,3.115 6,3.292 0.479,0.177 10 false 12

C334428E02
5.906,0.344 6.552,0.552 0.646,0.208 10 false BATT 5.906,0.688 6.552,0.896 0.646,0.208 10 false +B 5.906,1.052 6.552,1.26 0.646,0.208 10 false +B2 5.906,1.438 6.552,1.646 0.646,0.208 10 false MREL 5.906,2.844 6.552,3.052 0.646,0.208 10 false E02 5.906,3.208 6.552,3.417 0.646,0.208 10 false E01 5.906,2.135 6.552,2.344 0.646,0.208 10 false ME01 3.438,0.135 3.708,0.323 0.271,0.188 10 false EFI 1.771,0.26 2.583,0.469 0.813,0.208 10 false from Battery 1.594,0.625 2.958,0.854 1.365,0.229 10 false from EFI Relay 0.094,0.01 1.458,0.24 1.365,0.229 12 false for 2TR-FE: 1.75,1.354 2.938,1.583 1.188,0.229 10 false to EFI Relay 5.458,0.344 5.823,0.563 0.365,0.219 10 false G180 5.458,0.698 5.823,0.917 0.365,0.219 10 false G180 5.458,1.438 5.823,1.656 0.365,0.219 10 false G181 5.458,1.792 5.823,2.01 0.365,0.219 10 false G180 5.458,2.146 5.823,2.365 0.365,0.219 10 false C153 5.458,2.5 5.823,2.719 0.365,0.219 10 false C153 5.458,2.854 5.823,3.073 0.365,0.219 10 false C153 5.458,3.208 5.823,3.427 0.365,0.219 10 false C153 5.458,1.063 5.823,1.281 0.365,0.219 10 false G180 5.594,0.156 5.771,0.313 0.177,0.156 10 false 3 5.594,0.521 5.771,0.677 0.177,0.156 10 false 1 5.594,0.865 5.771,1.021 0.177,0.156 10 false 2 5.594,1.24 5.771,1.396 0.177,0.156 10 false 6 5.552,1.604 5.729,1.76 0.177,0.156 10 false 18 5.583,2.667 5.76,2.823 0.177,0.156 10 false 2 5.583,2.302 5.76,2.458 0.177,0.156 10 false 3 5.583,1.958 5.76,2.115 0.177,0.156 10 false 4 5.906,1.781 6.552,1.99 0.646,0.208 10 false EC 5.583,3.021 5.781,3.198 0.198,0.177 10 false 1 5.906,2.49 6.552,2.698 0.646,0.208 10 false E1 6.094,3.51 6.49,3.698 0.396,0.188 10 false ECM

C334430E02
5.906,0.313 6.552,0.521 0.646,0.208 10 false BATT 5.906,0.698 6.552,0.906 0.646,0.208 10 false +B 5.906,1.385 6.552,1.594 0.646,0.208 10 false MREL 5.906,2.833 6.552,3.042 0.646,0.208 10 false E01 5.906,2.115 6.552,2.323 0.646,0.208 10 false E1 3.438,0.177 3.708,0.365 0.271,0.188 10 false EFI 1.771,0.292 2.583,0.5 0.813,0.208 10 false from Battery 1.583,0.656 2.948,0.885 1.365,0.229 10 false from EFI Relay 0.094,0.01 1.458,0.24 1.365,0.229 12 false for 5L-E: 1.74,1.385 2.927,1.615 1.188,0.229 10 false to EFI Relay 5.458,0.323 5.823,0.542 0.365,0.219 10 false G183 5.458,0.688 5.823,0.906 0.365,0.219 10 false G183 5.438,1.417 5.802,1.635 0.365,0.219 10 false G183 5.458,1.771 5.823,1.99 0.365,0.219 10 false G183 5.458,2.125 5.823,2.344 0.365,0.219 10 false C161 5.458,2.479 5.823,2.698 0.365,0.219 10 false C161 5.458,2.844 5.823,3.063 0.365,0.219 10 false C161 5.594,0.146 5.771,0.302 0.177,0.156 10 false 2 5.594,0.521 5.771,0.677 0.177,0.156 10 false 1 5.552,1.229 5.729,1.385 0.177,0.156 10 false 10 5.583,1.594 5.76,1.75 0.177,0.156 10 false 7 5.583,2.656 5.76,2.813 0.177,0.156 10 false 7 5.583,2.313 5.76,2.469 0.177,0.156 10 false 6 5.583,1.948 5.76,2.104 0.177,0.156 10 false 5 5.906,1.76 6.552,1.969 0.646,0.208 10 false EC 5.906,2.469 6.552,2.677 0.646,0.208 10 false E02 6.094,3.458 6.49,3.646 0.396,0.188 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

for 1KD-FTV:

i.

Disconnect the C93, G57 and G58 ECM connectors.

U170372E01
0.094,0.076 0.365,0.323 0.270,0.246 10 *a 0.284,0.838 0.558,0.979 0.274,0.141 10 C93 2.774,0.838 3.055,0.979 0.281,0.141 10 G57 5.091,0.838 5.372,0.979 0.281,0.141 10 G58 0.872,0.7 0.661,0.49 0.661,0.49 0.553,0.49 false 0.619,1.537 0.732,1.537 0.732,1.537 1.117,1.141 false 1.377,1.141 1.677,1.663 1.677,1.663 1.817,1.663 false 1.39,0.871 1.849,0.409 1.849,0.409 2.059,0.409 false 3.916,0.85 4.285,0.518 4.285,0.518 4.423,0.518 false 4.549,0.892 4.427,0.892 4.427,0.892 4.217,1.026 false 3.916,1.313 4.108,1.688 4.108,1.688 4.199,1.688 false 6.608,0.675 6.485,0.675 6.485,0.675 6.289,0.812 false 4.474,1.49 4.348,1.49 4.348,1.49 4.147,1.313 false 6.637,0.616 7.064,0.758 0.427,0.142 10 MREL 4.441,0.458 4.868,0.600 0.427,0.142 10 EC 4.563,0.829 4.990,0.971 0.427,0.142 10 +B2 4.493,1.414 4.920,1.556 0.427,0.142 10 +B 4.217,1.614 4.643,1.756 0.427,0.142 10 BATT 2.075,0.344 2.502,0.486 0.427,0.142 10 ME01 1.837,1.605 2.263,1.747 0.427,0.142 10 E02 0.348,1.474 0.775,1.616 0.427,0.142 10 E01 0.348,0.416 0.775,0.558 0.427,0.142 10 E1

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C93-1 (E1) - Body ground Always Below 1 Ω
C93-12 (E01) - Body ground Always Below 1 Ω
C93-13 (E02) - Body ground Always Below 1 Ω
C93-8 (ME01) - Body ground Always Below 1 Ω
G57-11 (EC) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G57-23 (BATT) - Body ground Always 11 to 14 V
G57-17 (+B2) - Body ground Battery positive (+) voltage applied to terminal G58-11 (MREL) 11 to 14 V
G57-24 (+B) - Body ground Battery positive (+) voltage applied to terminal G58-11 (MREL) 11 to 14 V




b.

for 2TR-FE:

i.

Disconnect the C153, G180 and C181 ECM connectors.

U170540E01
0.084,0.057 0.355,0.303 0.270,0.246 10 *a 3.38,0.135 3.754,0.276 0.375,0.141 10 G180 5.488,0.135 5.863,0.276 0.375,0.141 10 G181 1.32,0.135 1.695,0.276 0.375,0.141 10 C153 1.513,0.771 1.881,0.295 1.881,0.295 1.989,0.295 false 1.019,0.852 0.827,1.03 0.827,1.03 0.704,1.03 false 3.417,0.769 3.048,0.149 3.048,0.149 2.909,0.149 false 3.267,0.746 2.956,0.49 2.956,0.49 2.865,0.49 false 6.478,0.614 6.356,0.614 6.356,0.614 6.16,0.75 false 2.79,1.024 2.916,1.024 2.916,1.024 3.107,0.859 false 6.508,0.554 6.935,0.696 0.427,0.142 10 MREL 2.529,0.074 2.956,0.216 0.427,0.142 10 BATT 2.571,0.953 2.998,1.095 0.427,0.142 10 +B 2.012,0.202 2.439,0.344 0.427,0.142 10 ME01 0.429,0.959 0.856,1.101 0.427,0.142 10 E01 2.55,0.414 2.977,0.556 0.427,0.142 10 +B2 2.797,1.368 2.909,1.368 2.909,1.368 3.1,1.167 false 2.567,1.305 2.994,1.447 0.427,0.142 10 EC 0.707,0.524 0.819,0.524 0.819,0.524 1.201,0.754 false 0.433,0.461 0.859,0.603 0.427,0.142 10 E02 0.84,0.216 0.952,0.216 0.952,0.216 1.359,0.751 false 0.622,0.153 1.048,0.295 0.427,0.142 10 E1

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C153-3 (E1) - Body ground Always Below 1 Ω
C153-1 (E01) - Body ground Always Below 1 Ω
C153-2 (E02) - Body ground Always Below 1 Ω
C153-4 (ME01) - Body ground Always Below 1 Ω
G180-18 (EC) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G180-3 (BATT) - Body ground Always 11 to 14 V
G180-1 (+B) - Body ground Battery positive (+) voltage applied to terminal G181-6 (MREL) 11 to 14 V
G180-2 (+B2) - Body ground Battery positive (+) voltage applied to terminal G181-6 (MREL) 11 to 14 V




c.

for 5L-E:

i.

Disconnect the C161 and C183 ECM connectors.

U170541E01
0.084,0.085 0.355,0.331 0.270,0.246 10 *a 5.11,0.163 5.484,0.304 0.375,0.141 10 G183 1.625,0.163 1.999,0.304 0.375,0.141 10 C161 2.27,0.859 2.462,1.038 2.462,1.038 2.585,1.038 false 4.989,0.759 4.673,0.409 4.673,0.409 4.534,0.409 false 6.052,0.605 5.929,0.605 5.929,0.605 5.733,0.742 false 4.503,1.034 4.629,1.034 4.629,1.034 4.806,0.87 false 4.105,1.272 4.532,1.414 0.427,0.142 10 MREL 4.154,0.333 4.581,0.475 0.427,0.142 10 BATT 4.284,0.964 4.710,1.106 0.427,0.142 10 +B 2.604,0.969 3.031,1.111 0.427,0.142 10 E01 4.508,1.335 4.655,1.335 4.655,1.335 5.026,1.023 false 6.068,0.536 6.495,0.678 0.427,0.142 10 EC 2.582,0.531 2.47,0.531 2.47,0.531 2.088,0.761 false 2.604,0.461 3.031,0.603 0.427,0.142 10 E02 2.449,0.223 2.337,0.223 2.337,0.223 1.93,0.758 false 2.475,0.146 2.901,0.288 0.427,0.142 10 E1

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C161-5 (E1) - Body ground Always Below 1 Ω
C161-7 (E01) - Body ground Always Below 1 Ω
C161-6 (E02) - Body ground Always Below 1 Ω
G183-7 (EC) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G183-2 (BATT) - Body ground Always 11 to 14 V
G183-1 (+B) - Body ground Battery positive (+) voltage applied to terminal G183-10 (MREL) 11 to 14 V




Result
Result Proceed to
OK (for 1KD-FTV) A
OK (for 2TR-FE) B
OK (for 5L-E) C
NG D


A

B

C

D

REPAIR OR REPLACE HARNESS OR CONNECTOR