Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) › 2015.06–2016.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261032 CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)  Open in CAN Main Wire  


DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
·

CAN main wire and connector

·

ECM

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 3 junction connector

·

No. 4 junction connector*1

·

No. 5 junction connector*2

·

Combination meter assembly

·

DLC3 CAN branch wire or connector



*1: for 2TR-FE, 5L-E

*2: for 1KD-FTV


WIRING DIAGRAM

C334420E01
6.014,3.844 6.433,4.020 0.419,0.176 10 DLC3 6.014,3.697 6.433,3.873 0.419,0.176 10 G48 5.892,2.893 6.302,3.031 0.411,0.138 10 CANH 5.697,2.781 5.803,2.920 0.105,0.139 10 6 5.608,3.21 5.802,3.349 0.194,0.138 10 14 5.892,3.31 6.282,3.448 0.390,0.138 10 CANL 5.626,5.551 6.839,5.941 1.213,0.391 10 G6 5.626,5.719 6.839,6.109 1.213,0.391 10 Combination Meter Assembly 5.892,4.595 6.358,4.736 0.466,0.141 10 CANH 5.892,5.242 6.358,5.418 0.466,0.176 10 CANL 5.892,4.595 6.358,4.736 0.466,0.141 10 CANH 5.892,5.242 6.358,5.418 0.466,0.176 10 CANL 5.63,4.595 6.096,4.736 0.466,0.141 10 40 5.63,5.055 6.096,5.231 0.466,0.176 10 39 3.51,4.595 3.976,4.736 0.466,0.141 10 6*1 3.454,5.055 3.975,5.231 0.522,0.176 10 17*1 2.884,4.595 3.350,4.736 0.466,0.141 10 *1 2.884,5.055 3.406,5.231 0.522,0.176 10 *1 3.757,5.949 4.223,6.091 0.466,0.141 10 *1 3.757,6.409 4.279,6.585 0.522,0.176 10 *1 2.496,4.595 2.962,4.736 0.466,0.141 10 9 2.496,5.055 3.018,5.231 0.522,0.176 10 20 2.496,5.951 2.962,6.092 0.466,0.141 10 10 2.496,6.411 3.018,6.587 0.522,0.176 10 21 4.612,4.595 5.078,4.736 0.466,0.141 10 2*2, *3 4.612,5.055 5.127,5.231 0.515,0.176 10 13*2, *3 3.483,5.41 4.696,5.801 1.213,0.391 10 G94 3.483,5.552 5.078,5.796 1.595,0.244 10 No. 3 Junction Connector 1.564,6.812 2.777,7.202 1.213,0.391 10 A73 1.564,6.98 3.506,7.224 1.942,0.244 10 No. 5 Junction Connector*1 4.612,2.785 4.787,2.927 0.176,0.141 10 5 4.612,3.245 4.807,3.421 0.195,0.176 10 16 3.661,2.785 3.764,2.927 0.103,0.141 10 1 3.568,3.245 3.763,3.421 0.195,0.176 10 12 3.071,2.785 3.246,2.927 0.176,0.141 10 6 3.071,3.245 3.266,3.421 0.195,0.176 10 17 2.12,2.785 2.223,2.927 0.103,0.141 10 1 2.027,3.245 2.222,3.421 0.195,0.176 10 12 2.496,0.583 2.672,0.725 0.176,0.141 10 10 2.496,1.015 2.692,1.191 0.195,0.176 10 21 1.546,0.583 1.649,0.725 0.103,0.141 10 9 1.453,1.015 1.648,1.191 0.195,0.176 10 20 1.851,3.673 3.064,4.064 1.213,0.391 10 G100 1.851,3.841 3.446,4.085 1.595,0.244 10 No. 2 Junction Connector 1.277,1.443 2.490,1.834 1.213,0.391 10 A72 1.277,1.611 3.254,1.855 1.977,0.244 10 No. 4 Junction Connector*2, *3 1.852,2.09 2.318,2.231 0.466,0.141 10 *1 2.784,1.01 3.250,1.151 0.466,0.141 10 *2, *3 2.784,0.583 3.250,0.724 0.466,0.141 10 *2, *3 0.85,1.01 1.316,1.151 0.466,0.141 10 *2, *3 0.85,0.583 1.316,0.724 0.466,0.141 10 *2, *3 1.852,0.058 2.318,0.199 0.466,0.141 10 *1 0.023,3.673 1.236,4.064 1.213,0.391 10 G97 0.023,3.841 1.618,4.085 1.595,0.244 10 No. 1 Junction Connector 3.071,2.785 3.246,2.927 0.176,0.141 10 6 3.071,3.245 3.266,3.421 0.195,0.176 10 17 2.12,2.785 2.223,2.927 0.103,0.141 10 1 2.027,3.245 2.222,3.421 0.195,0.176 10 12 0.478,2.553 0.653,2.694 0.176,0.141 10 6 0.884,2.553 1.079,2.729 0.195,0.176 10 17 1.101,2.77 1.204,2.911 0.103,0.141 10 1 1.101,3.23 1.296,3.406 0.195,0.176 10 12 5.892,0.575 6.358,0.716 0.466,0.141 10 CANH 5.892,1.221 6.358,1.398 0.466,0.176 10 CANL 6.033,1.513 6.486,1.705 0.453,0.192 10 ECM 5.061,0.67 5.423,0.813 0.362,0.143 10 G181 5.061,1.123 5.423,1.266 0.362,0.143 10 G181 5.091,0.483 5.397,0.624 0.306,0.141 10 13*2 5.09,0.933 5.399,1.076 0.309,0.143 10 14*2 4.643,0.67 5.005,0.813 0.362,0.143 10 G183 4.643,1.123 5.005,1.266 0.362,0.143 10 G183 4.673,0.483 4.979,0.624 0.306,0.141 10 25*3 4.672,0.933 4.981,1.076 0.309,0.143 10 31*3 5.498,0.67 5.788,0.813 0.290,0.143 10 G58 5.498,1.123 5.788,1.266 0.290,0.143 10 G58 5.5,0.483 5.806,0.624 0.306,0.141 10 35*1 5.499,0.933 5.807,1.076 0.309,0.143 10 36*1 0.168,6.953 2.110,7.099 1.942,0.146 10 *1: for 1KD-FTV 0.191,7.235 2.133,7.381 1.942,0.146 10 *2: for 2TR-FE 0.191,7.517 2.133,7.663 1.942,0.146 10 *3: for 5L-E

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - DLC3)
2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - DLC3)
a.
U148936E01
1.948,2.512 1.763,2.164 1.763,2.164 1.623,2.164 false 1.931,2.959 2.069,3.208 2.069,3.208 2.209,3.208 false 1.847,1.291 2.127,1.649 2.127,1.649 2.224,1.649 false 2.349,0.682 2.235,0.682 2.235,0.682 1.847,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.371,0.605 2.791,0.747 0.420,0.142 10 CANH 2.242,1.564 2.665,1.706 0.424,0.142 10 CANL 2.244,3.14 2.668,3.282 0.424,0.142 10 CANL 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 1.101,2.087 1.521,2.229 0.420,0.142 10 CANH 0.427,1.094 0.708,1.232 0.281,0.138 10 G94

Disconnect the G94 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G94-5 (CANH) - G48-6 (CANH) Ignition switch off Below 1 Ω
G94-16 (CANL) - G48-14 (CANL) Ignition switch off Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM)
a.
U148891E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.447,1.259 0.731,1.396 0.284,0.137 10 G94

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G94-1 (CANH) - G94-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U148892E01
2.497,1.038 2.396,1.038 2.396,1.038 2.158,1.234 false 2.158,1.439 2.343,1.693 2.343,1.693 2.466,1.693 false 2.515,0.961 3.120,1.098 0.605,0.137 10 CANH*B 2.494,1.612 3.064,1.748 0.570,0.137 10 CANL*B 2.383,0.632 2.282,0.632 2.282,0.632 1.754,1.234 false 1.754,1.439 1.956,1.936 1.956,1.936 2.079,1.936 false 2.401,0.555 3.006,0.692 0.605,0.137 10 CANH*A 2.107,1.854 2.677,1.991 0.570,0.137 10 CANL*A 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.447,1.259 0.731,1.396 0.284,0.137 10 G94

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Switch Condition Specified Condition
G94-6 (CANH) - G94-17 (CANL) Ignition switch off 108 to 132 Ω

for 2TR-FE, 5L-E
Tester Connection Switch Condition Specified Condition
G94-2 (CANH) - G94-13 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*A for 1KD-FTV
*B for 2TR-FE, 5L-E
*a Rear view of wire harness connector
(to No. 3 Junction Connector)

Result
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 2TR-FE, 5L-E) C



A

REPLACE NO. 3 JUNCTION CONNECTOR

B

20.CONNECT CONNECTOR

C

25.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the G94 No. 3 junction connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ECM)
6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ECM)
a.
U148893E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G100

Disconnect the G100 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G100-1 (CANH) - G100-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

NG

8.CONNECT CONNECTOR
7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U148894E01
2.383,0.632 2.282,0.632 2.282,0.632 1.754,1.234 false 1.754,1.439 1.956,1.936 1.956,1.936 2.079,1.936 false 2.401,0.555 3.006,0.692 0.605,0.137 10 CANH 2.107,1.854 2.677,1.991 0.570,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.372,1.259 0.729,1.396 0.357,0.137 10 G100

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G100-6 (CANH) - G100-17 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the G100 No. 2 junction connector.



NEXT

9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)
9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)
a.
U148895E01
2.383,0.632 2.282,0.632 2.282,0.632 1.754,1.234 false 1.754,1.439 1.956,1.936 1.956,1.936 2.079,1.936 false 2.401,0.555 3.006,0.692 0.605,0.137 10 CANH 2.107,1.854 2.677,1.991 0.570,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.395,1.259 0.679,1.396 0.284,0.137 10 G97

Disconnect the G97 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G97-6 (CANH) - G97-17 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)

Result
Result Proceed to
OK A
NG (for 2TR-FE, 5L-E) B
NG (for 1KD-FTV) C



A

10.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

B

11.CONNECT CONNECTOR

C

14.CONNECT CONNECTOR
10.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U148896E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.411,1.259 0.699,1.396 0.288,0.137 10 G97

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G97-1 (CANH) - G97-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

11.CONNECT CONNECTOR
a.

Reconnect the G97 No. 1 junction connector.



NEXT

12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - ECM)
12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - ECM)
a.
U148889E01
1.006,0.963 1.107,0.963 1.107,0.963 1.31,1.234 false 1.31,1.439 1.171,1.699 1.171,1.699 1.048,1.699 false 0.497,0.886 0.918,1.022 0.421,0.137 10 CANH 0.565,1.618 0.961,1.755 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A72

Disconnect the A72 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-10 (CANH) - A72-21 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)

Result
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 5L-E) C



A

13.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

B

16.CONNECT CONNECTOR

C

18.CONNECT CONNECTOR
13.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U148890E01
1.032,0.862 1.133,0.862 1.133,0.862 1.414,1.234 false 1.414,1.439 1.227,1.755 1.227,1.755 1.104,1.755 false 0.523,0.784 0.944,0.921 0.421,0.137 10 CANH 0.621,1.674 1.017,1.810 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-9 (CANH) - A72-20 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

14.CONNECT CONNECTOR
a.

Reconnect the G97 No. 1 junction connector.



NEXT

15.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 1 JUNCTION CONNECTOR)
15.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 1 JUNCTION CONNECTOR)
a.
U170369E01
0.08,0.062 0.282,0.291 0.202,0.230 10 *a 0.485,1.077 0.770,1.219 0.286,0.142 10 G58 2.087,1.573 2.2,1.72 2.2,1.72 2.355,1.72 false 2.335,1.976 2.133,1.976 2.133,1.976 1.982,1.573 false 2.383,1.643 2.867,1.785 0.483,0.142 10 CANL 2.36,1.898 2.843,2.040 0.483,0.142 10 CANH

Disconnect the G58 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G58-35 (CANH) - G58-36 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 1 JUNCTION CONNECTOR)

16.CONNECT CONNECTOR
a.

Reconnect the A72 No. 4 junction connector.



NEXT

17.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 4 JUNCTION CONNECTOR)
17.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 4 JUNCTION CONNECTOR)
a.
U170531E02
2.594,1.031 2.385,1.031 2.385,1.031 2.104,1.219 false 2.5,0.531 2.292,0.531 2.292,0.531 1.979,1.219 false 0.083,0 0.281,0.229 0.198,0.229 10 false *a 0.365,1.115 0.729,1.26 0.365,0.146 10 false G181 2.635,0.958 3.115,1.104 0.479,0.146 10 false CANL 2.531,0.458 3.01,0.604 0.479,0.146 10 false CANH

Disconnect the G181 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G181-13 (CANH) - G181-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 4 JUNCTION CONNECTOR)

18.CONNECT CONNECTOR
a.

Reconnect the A72 No. 4 junction connector.



NEXT

19.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 4 JUNCTION CONNECTOR)
19.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 4 JUNCTION CONNECTOR)
a.
U170533E01
0.05,0.057 0.252,0.287 0.202,0.230 10 *a 0.277,1.073 0.643,1.215 0.365,0.142 10 G183 2.641,1.868 2.439,1.868 2.439,1.868 2.257,1.646 false 2.665,1.791 3.149,1.933 0.483,0.142 10 CANL 2.641,1.241 2.439,1.241 2.439,1.241 2.257,1.394 false 2.665,1.164 3.149,1.306 0.483,0.142 10 CANH

Disconnect the G183 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G183-25 (CANH) - G183-31 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 4 JUNCTION CONNECTOR)

20.CONNECT CONNECTOR
a.

Reconnect the G94 No. 3 junction connector.



NEXT

21.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
21.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U148898E01
1.006,0.963 1.107,0.963 1.107,0.963 1.31,1.234 false 1.31,1.439 1.171,1.699 1.171,1.699 1.048,1.699 false 0.497,0.886 0.918,1.022 0.421,0.137 10 CANH 0.565,1.618 0.961,1.755 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A73

Disconnect the A73 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-10 (CANH) - A73-21 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

22.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

NG

23.CONNECT CONNECTOR
22.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U148897E01
1.032,0.862 1.133,0.862 1.133,0.862 1.414,1.234 false 1.414,1.439 1.227,1.755 1.227,1.755 1.104,1.755 false 0.523,0.784 0.944,0.921 0.421,0.137 10 CANH 0.621,1.674 1.017,1.810 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A73

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-9 (CANH) - A73-20 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

23.CONNECT CONNECTOR
a.

Reconnect the A73 No. 5 junction connector.



NEXT

24.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)
24.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)
a.
U148233E01
0.723,0.39 0.931,0.530 0.208,0.139 10 G6 1.935,0.186 2.374,0.322 0.440,0.137 10 CANH 1.724,0.437 2.163,0.574 0.440,0.137 10 CANL 0.074,0.063 0.404,0.245 0.330,0.183 10 *a 2.938,1.372 2.609,0.275 2.609,0.275 2.454,0.275 false 2.809,1.369 2.375,0.514 2.375,0.514 2.221,0.514 false

Disconnect the G6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 5 JUNCTION CONNECTOR)

25.CONNECT CONNECTOR
a.

Reconnect the G94 No. 3 junction connector.



NEXT

26.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)
26.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)
a.
U148233E01
0.723,0.39 0.931,0.530 0.208,0.139 10 G6 1.935,0.186 2.374,0.322 0.440,0.137 10 CANH 1.724,0.437 2.163,0.574 0.440,0.137 10 CANL 0.074,0.063 0.404,0.245 0.330,0.183 10 *a 2.938,1.372 2.609,0.275 2.609,0.275 2.454,0.275 false 2.809,1.369 2.375,0.514 2.375,0.514 2.221,0.514 false

Disconnect the G6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)