Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261032 CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)  U0182  Lost Communication with AFS ECU  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0182 There is no communication from the headlight swivel ECU assembly.
·

Power source circuit of headlight swivel ECU assembly

·

Headlight swivel ECU assembly CAN branch wire or connector

·

Headlight swivel ECU assembly



For vehicles with a LED headlight.


WIRING DIAGRAM

C334427E01
5.38,3.969 5.679,4.107 0.299,0.137 10 A58 5.38,4.119 6.777,4.427 1.397,0.309 10 Headlight Swivel ECU Assembly 0.453,1.926 2.285,2.063 1.832,0.137 10 A73 1.691,1.506 1.939,1.643 0.248,0.137 10 15 1.691,0.917 1.939,1.055 0.248,0.137 10 4 5.343,1.506 5.531,1.643 0.188,0.137 10 13 5.343,0.917 5.531,1.055 0.188,0.137 10 12 5.656,1.594 6.140,1.732 0.485,0.137 10 CANL 5.656,1.006 6.140,1.143 0.485,0.137 10 CANH 5.343,2.405 5.531,2.542 0.188,0.137 10 15 5.656,2.493 6.140,2.631 0.485,0.137 10 IG 1.761,2.493 3.083,2.631 1.323,0.137 10 from IG1 NO.1 Relay 5.343,3.241 5.531,3.378 0.188,0.137 10 22 5.656,3.329 6.140,3.467 0.485,0.137 10 E1 0.453,2.089 2.451,2.227 1.998,0.137 10 No. 5 Junction Connector 3.917,2.377 4.791,2.523 0.873,0.147 10 ECU-IG NO.1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY CAN BRANCH WIRE)
a.
U170208E04
2.406,1.823 2.51,1.823 2.51,1.823 2.76,1.115 false 2.813,0.479 2.708,0.479 2.708,0.479 2.615,1.042 false 1.563,0.271 1.844,0.469 0.281,0.198 10 false A58 2.854,0.406 3.313,0.594 0.458,0.188 10 false CANH 1.927,1.74 2.396,1.896 0.469,0.156 10 false CANL 0.104,0.063 0.354,0.292 0.25,0.229 10 false *a

Disconnect the A58 headlight swivel ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A58-12 (CANH) - A58-13 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170210E02
1.833,1.677 1.688,1.677 1.688,1.677 1.552,1.24 false 0.417,1.635 0.531,1.635 0.531,1.635 0.719,1.24 false 1.552,0.25 1.833,0.448 0.281,0.198 10 false A58 0.229,1.552 0.427,1.708 0.198,0.156 10 false IG 1.865,1.594 2.354,1.74 0.49,0.146 10 false E1 0.104,0.073 0.354,0.302 0.25,0.229 10 false *a

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-22 (E1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A58-15 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly)


OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR