Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on "Bus Check".

·

"Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside center airbag sensor assembly

·

Center airbag sensor assembly CAN branch wire or connector

·

Center airbag sensor assembly



WIRING DIAGRAM

C201307E06
5.486,2.141 5.979,2.315 0.493,0.174 10 E1 5.486,1.684 5.980,1.896 0.494,0.211 10 IG2 4.895,3.352 6.949,3.544 2.054,0.192 10 Center Airbag Sensor Assembly 5.486,2.56 5.979,2.734 0.493,0.174 10 E2 4.535,1.561 4.838,1.735 0.303,0.174 10 IGN 2.749,1.686 3.719,1.872 0.969,0.186 10 from IG2 Relay 5.186,2.043 5.398,2.205 0.212,0.161 10 25 5.186,2.485 5.398,2.633 0.213,0.148 10 26 5.186,1.609 5.359,1.785 0.174,0.176 10 21 5.486,1.053 5.980,1.264 0.494,0.211 10 CANL 5.186,0.977 5.359,1.153 0.174,0.176 10 22 5.486,0.624 5.980,0.835 0.494,0.211 10 CANH 5.186,0.549 5.359,0.725 0.174,0.176 10 13 1.784,0.977 1.957,1.153 0.174,0.176 10 16 1.784,0.549 1.957,0.725 0.174,0.176 10 5 4.895,3.194 5.280,3.342 0.385,0.148 10 G1 0.429,1.521 2.031,1.713 1.601,0.192 10 No. 2 Junction Connector 0.429,1.363 0.805,1.511 0.375,0.148 10 G132

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U169938E01
0.041,0 0.230,0.177 0.189,0.177 10 *a 0.132,1.336 0.551,1.513 0.419,0.177 10 CANH 0.235,0.987 0.549,1.164 0.314,0.177 10 G1 0.312,1.769 0.732,1.946 0.419,0.177 10 CANL 1.279,1.077 0.725,1.419 0.725,1.419 0.652,1.419 false 1.176,1.487 0.95,1.863 0.95,1.863 0.823,1.863 false

Disconnect the G1 center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G1-13 (CANH) - G1-22 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
U169937E01
0.041,0 0.230,0.177 0.189,0.177 10 *a 1.19,1.855 1.410,2.032 0.221,0.177 10 E1 2.062,1.855 2.283,2.032 0.221,0.177 10 E2 0.371,1.656 0.620,1.833 0.249,0.177 10 IG2 1.659,1.495 1.513,1.937 1.513,1.937 1.439,1.937 false 1.808,1.495 1.955,1.937 1.955,1.937 2.028,1.937 false 1.029,1.492 0.797,1.751 0.797,1.751 0.67,1.751 false 0.235,0.981 0.549,1.158 0.314,0.177 10 G1

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-25 (E1) - Body ground Always Below 1 Ω
G1-26 (E2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G1-21 (IG2) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR