Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptoms Trouble Area
Certification ECU Communication Stop Mode Either condition is met:
·

"Certification (Smart)" is not displayed on "Bus Check".

·

"Certification ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside certification ECU (smart key ECU assembly)

·

Certification ECU (smart key ECU assembly) CAN branch wire or connector

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

E346822E01
0.625,1.354 1.24,1.552 0.615,0.198 10 false G134 0.635,1.521 2.208,1.802 1.573,0.281 10 false No. 3 Junction Connector 1.719,0.323 2.333,0.521 0.615,0.198 10 false 6 1.729,0.708 2.344,0.906 0.615,0.198 10 false 17 5.656,0.292 6.271,0.49 0.615,0.198 10 false 9 5.865,0.417 6.479,0.615 0.615,0.198 10 false CANH 5.875,0.823 6.49,1.021 0.615,0.198 10 false CANL 5.604,0.74 6.219,0.938 0.615,0.198 10 false 10 5.854,1.365 6.469,1.563 0.615,0.198 10 false +B 5.667,1.25 6.281,1.448 0.615,0.198 10 false 1 5.854,1.76 6.469,1.958 0.615,0.198 10 false CUTB 5.594,1.688 6.208,1.885 0.615,0.198 10 false 17 5.854,2.188 6.469,2.385 0.615,0.198 10 false IG 5.604,2.083 6.219,2.281 0.615,0.198 10 false 16 5.844,2.625 6.458,2.823 0.615,0.198 10 false E 5.615,2.5 6.229,2.698 0.615,0.198 10 false 15 4.917,2.052 5.531,2.25 0.615,0.198 10 false IGN 4.854,1.667 5.469,1.865 0.615,0.198 10 false ECU-B 4.813,1.24 5.427,1.438 0.615,0.198 10 false SMART 3.135,1.354 4.135,1.656 1,0.302 10 false from Battery 3.146,1.771 4.146,2.073 1,0.302 10 false from Battery 2.969,2.167 3.969,2.469 1,0.302 10 false from IG2 Relay 5.365,2.927 6.365,3.229 1,0.302 10 false G38 5.396,3.094 6.906,3.615 1.51,0.521 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (CERTIFICATION ECU CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (CERTIFICATION ECU CAN BRANCH WIRE)
a.
U148226E03
1.229,1.563 1.01,0.958 1.01,0.958 0.938,0.958 true 1.135,1.552 0.646,1.156 0.646,1.156 0.573,1.156 true 0.49,0.885 0.917,1.042 0.427,0.156 10 false CANH 0.177,1.083 0.573,1.24 0.396,0.156 10 false CANL 2.5,1.406 2.823,1.563 0.323,0.156 10 false G38 0.073,0 0.396,0.156 0.323,0.156 10 false *a

Disconnect the G38 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G38-9 (CANH) - G38-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CERTIFICATION ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)
a.
U148227E03
2.188,1.542 2.427,1.271 2.427,1.271 2.5,1.271 true 0.865,1.563 0.719,1.323 0.719,1.323 0.646,1.323 true 2.208,1.635 2.51,1.479 2.51,1.479 2.583,1.479 true 2.125,1.667 2.385,1.938 2.385,1.938 2.458,1.938 true 2.625,1.406 2.813,1.563 0.188,0.156 10 false IG 2.542,1.188 2.781,1.344 0.24,0.156 10 false +B 0.5,1.25 0.646,1.406 0.146,0.156 10 false E 2.49,1.875 2.938,2.063 0.448,0.188 10 false CUTB 0.219,1.49 0.542,1.646 0.323,0.156 10 false G38 0.115,0 0.365,0.156 0.25,0.156 10 false *a

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-15 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G38-1 (+B) - Body ground Always 11 to 14 V
G38-17 (CUTB) - Body ground Always 11 to 14 V
G38-16 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR