Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  Open in CAN Main Wire  


DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
·

CAN main wire and connector

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 3 junction connector

·

ECM

·

Combination meter assembly

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C329312E01
6.103,1.8 6.464,1.977 0.361,0.176 10 ECM 0.342,4.596 0.687,4.772 0.345,0.176 10 G48 0.342,4.756 0.761,4.932 0.419,0.176 10 DLC3 5.729,3.549 6.124,3.725 0.395,0.176 10 G6 5.729,3.708 6.954,4.072 1.225,0.364 10 Combination Meter Assembly 2.224,1.738 2.624,1.914 0.401,0.176 10 G134 2.224,1.897 3.891,2.073 1.667,0.176 10 No. 3 Junction Connector 3.345,3.549 3.745,3.725 0.401,0.176 10 A72 3.345,3.708 5.011,3.884 1.667,0.176 10 No. 1 Junction Connector 1.275,4.721 1.714,4.897 0.439,0.176 10 G132 1.275,4.881 3.075,5.057 1.800,0.176 10 No. 2 Junction Connector 5.915,0.711 6.381,0.887 0.466,0.176 10 CANH 0.461,3.814 0.928,3.990 0.466,0.176 10 CANH 5.127,1.101 5.441,1.254 0.314,0.154 10 25*1 5.122,0.623 5.433,0.777 0.311,0.153 10 31*1 5.533,1.101 5.848,1.254 0.314,0.154 10 36*2 5.529,0.623 5.839,0.777 0.311,0.153 10 35*2 3.538,0.772 3.646,0.926 0.109,0.154 10 2 3.538,1.226 3.732,1.379 0.194,0.153 10 13 2.41,0.772 2.536,0.926 0.126,0.154 10 1 2.359,1.226 2.553,1.379 0.194,0.153 10 12 2.536,2.57 2.727,2.724 0.191,0.154 10 8 2.536,3 2.730,3.153 0.194,0.153 10 19 4.658,2.57 4.849,2.724 0.191,0.154 10 10 4.658,3 4.853,3.153 0.194,0.153 10 21 1.447,2.57 1.552,2.724 0.105,0.154 10 1 1.357,3 1.552,3.153 0.194,0.153 10 12 1.447,3.733 1.552,3.887 0.105,0.154 10 4 1.357,4.162 1.552,4.316 0.194,0.153 10 15 3.555,2.57 3.661,2.724 0.105,0.154 10 9 3.466,3 3.660,3.153 0.194,0.153 10 20 0.976,3.733 1.082,3.887 0.105,0.154 10 6 0.976,4.162 1.170,4.316 0.194,0.153 10 14 5.915,1.399 6.381,1.576 0.466,0.176 10 CANL 5.915,2.548 6.381,2.724 0.466,0.176 10 CANH 5.658,2.57 5.852,2.724 0.194,0.154 10 40 5.658,3 5.852,3.153 0.194,0.153 10 39 5.915,3.237 6.381,3.413 0.466,0.176 10 CANL 0.487,4.251 0.894,4.427 0.408,0.176 10 CANL 5.11,1.301 5.420,1.454 0.310,0.154 10 G56 5.516,1.301 5.826,1.454 0.310,0.154 10 G58 5.11,0.838 5.420,0.992 0.310,0.154 10 G56 4.665,1.101 4.979,1.254 0.314,0.154 10 28*3 4.66,0.623 4.971,0.777 0.311,0.153 10 17*3 4.633,1.301 5.020,1.454 0.386,0.154 10 G184 4.633,0.838 5.034,0.992 0.400,0.154 10 G184 5.516,0.838 5.826,0.992 0.310,0.154 10 G58 3.867,4.755 5.581,4.908 1.714,0.153 10 *1: for 1GR-FE 3.867,5.084 5.581,5.237 1.714,0.153 10 *2: for 1KD-FTV 3.867,5.413 5.581,5.567 1.714,0.153 10 *3: for 1GD-FTV

CAUTION / NOTICE / HINT

HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - DLC3)
2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - DLC3)
a.
U170158E01
2.542,0.372 2.976,0.550 0.434,0.178 10 CANH 2.528,1.886 2.962,2.064 0.434,0.178 10 CANL 1.971,1.093 2.431,0.46 2.431,0.46 2.518,0.46 false 1.971,1.341 2.431,1.974 2.431,1.974 2.518,1.974 false 0.445,1.076 0.817,1.253 0.372,0.178 10 G132 0.445,2.637 0.769,2.815 0.324,0.178 10 G48 0.131,2.277 0.344,2.455 0.213,0.178 10 *b 1.941,2.936 2.215,3.174 2.215,3.174 2.302,3.174 false 0.131,0.033 0.344,0.211 0.213,0.178 10 *a 2.344,3.098 2.778,3.276 0.434,0.178 10 CANL 0.926,1.964 1.359,2.142 0.434,0.178 10 CANH 1.934,2.48 1.54,2.052 1.54,2.052 1.453,2.052 false

Disconnect the No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-4 (CANH) - G48-6 (CANH) Engine switch off Below 1 Ω
G132-15 (CANL) - G48-14 (CANL) Engine switch off Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)
a.
U170152E01
2.703,0.852 3.136,1.030 0.434,0.178 10 CANH 0.224,0.92 0.630,1.098 0.406,0.178 10 G132 0.073,0.027 0.286,0.205 0.213,0.178 10 *a 2.703,1.321 3.136,1.499 0.434,0.178 10 CANL 2.693,0.926 2.63,0.926 2.63,0.926 2.349,1.087 false 2.693,1.407 2.63,1.407 2.63,1.407 2.349,1.246 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-1 (CANH) - G132-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U170153E02
2.698,0.74 2.625,0.74 2.625,0.74 1.531,1.094 true 2.698,1.635 2.625,1.635 2.625,1.635 1.531,1.302 true 2.698,0.656 3.135,0.833 0.438,0.177 10 false CANH 0.271,0.885 0.677,1.063 0.406,0.177 10 false G132 0.073,0 0.281,0.177 0.208,0.177 10 false *a 2.708,1.573 3.146,1.75 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-8 (CANH) - G132-19 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

10.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM)
6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - ECM)
a.
U170154E02
2.698,0.656 2.625,0.656 2.625,0.656 2.208,1.094 true 2.698,1.625 2.625,1.625 2.625,1.625 2.198,1.281 true 2.708,0.573 3.146,0.75 0.438,0.177 10 false CANH 0.271,0.927 0.688,1.104 0.417,0.177 10 false G134 0.073,0.01 0.281,0.188 0.208,0.177 10 false *a 2.698,1.531 3.135,1.708 0.438,0.177 10 false CANL

Disconnect the No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-2 (CANH) - G134-13 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

NG

8.CONNECT CONNECTOR
7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U170155E01
2.703,0.852 3.136,1.030 0.434,0.178 10 CANH 0.284,0.861 0.691,1.039 0.407,0.178 10 G134 0.073,0.02 0.286,0.198 0.213,0.178 10 *a 2.703,1.321 3.136,1.499 0.434,0.178 10 CANL 2.693,0.926 2.63,0.926 2.63,0.926 2.349,1.087 false 2.693,1.409 2.63,1.409 2.63,1.409 2.344,1.244 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-1 (CANH) - G134-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)
a.

Disconnect the ECM connector.

U170481E01
0.107,0.089 0.304,0.270 0.197,0.180 10 *a 3.889,0.089 4.086,0.270 0.197,0.180 10 *b 2.554,1.375 3.199,1.531 0.645,0.156 10 CANL*A 0.508,2.076 1.086,2.232 0.578,0.156 10 CANL*B 2.438,2.381 3.189,2.540 0.751,0.159 10 CANH*A 0.639,2.333 1.258,2.492 0.619,0.159 10 CANH*B 3.674,1.273 4.345,1.431 0.671,0.158 10 CANH*C 3.773,2.376 4.342,2.540 0.568,0.164 10 CANL*C 2.176,1.712 2.458,1.449 2.458,1.449 2.539,1.449 false 2.187,1.987 2.342,2.447 2.342,2.447 2.422,2.447 false 1.33,1.993 1.171,2.149 1.171,2.149 1.09,2.149 false 1.469,1.989 1.326,2.399 1.326,2.399 1.245,2.399 false 4.72,1.475 4.361,1.333 4.361,1.333 4.28,1.333 false 4.721,1.724 4.422,2.445 4.422,2.445 4.341,2.445 false 1.077,0.171 1.390,0.349 0.313,0.178 10 G56 1.492,0.182 1.731,0.362 0.239,0.180 10 *A 2.058,0.171 2.371,0.349 0.313,0.178 10 G58 2.473,0.182 2.705,0.362 0.232,0.180 10 *B 5.098,0.171 5.487,0.349 0.389,0.178 10 G184 5.555,0.182 5.801,0.362 0.246,0.180 10 *C

*A for 1GR-FE *B for 1KD-FTV
*C for 1GD-FTV - -
*a Rear view of wire harness connector
(to ECM)
*b Front view of wire harness connector
(to ECM)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE
Tester Connection Switch Condition Specified Condition
G56-31 (CANH) - G56-25 (CANL) Engine switch off 108 to 132 Ω

for 1KD-FTV
Tester Connection Switch Condition Specified Condition
G58-35 (CANH) - G58-36 (CANL) Engine switch off 108 to 132 Ω

for 1GD-FTV
Tester Connection Switch Condition Specified Condition
G184-17 (CANH) - G184-28 (CANL) Engine switch off 108 to 132 Ω


Result
Result Proceed to
OK (for 1GR-FE) A
OK (for 1KD-FTV) B
OK (for 1GD-FTV) C
NG D



A

B

C

D

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 3 JUNCTION CONNECTOR)

10.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U170156E01
0.232,0.646 0.665,0.824 0.434,0.178 10 CANH 0.266,0.971 0.590,1.149 0.324,0.178 10 A72 0.073,0.037 0.286,0.215 0.213,0.178 10 *a 0.278,1.6 0.712,1.778 0.434,0.178 10 CANL 0.742,0.725 0.805,0.725 0.805,0.725 1.278,1.036 false 0.743,1.67 0.806,1.67 0.806,1.67 1.284,1.278 false

Disconnect the No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-10 (CANH) - A72-21 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

NG

13.CONNECT CONNECTOR
12.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U170157E01
0.401,0.43 0.835,0.608 0.434,0.178 10 CANH 0.303,0.876 0.627,1.054 0.324,0.178 10 A72 0.073,0.033 0.286,0.211 0.213,0.178 10 *a 0.47,1.51 0.903,1.688 0.434,0.178 10 CANL 0.94,0.504 1.003,0.504 1.003,0.504 1.389,1.067 false 0.94,1.597 1.003,1.597 1.003,1.597 1.387,1.286 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-9 (CANH) - A72-20 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

13.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)
14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)
a.
U169931E01
0.205,0.558 0.499,0.741 0.295,0.183 10 G6 1.958,0.186 2.397,0.369 0.440,0.183 10 CANH 1.79,0.427 2.230,0.610 0.440,0.183 10 CANL 0.098,0.063 0.427,0.245 0.330,0.183 10 *a 2.962,1.372 2.547,0.275 2.547,0.275 2.477,0.275 false 2.833,1.369 2.312,0.514 2.312,0.514 2.244,0.514 false

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)