Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U1100  Lost Communication with Seat Belt Control ECU  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1100 There is no communication from the seat belt control ECU.
·

Power source or inside seat belt control ECU

·

Seat belt control ECU CAN branch wire or connector

·

Seat belt control ECU



For vehicles with a pre-crash safety system.


WIRING DIAGRAM

E346817E05
0.323,1.854 0.938,2.052 0.615,0.198 10 false G95 0.333,2.031 1.958,2.24 1.625,0.208 10 false No. 2 Junction Connector 1.938,0.938 2.552,1.135 0.615,0.198 10 false 6 1.938,1.344 2.552,1.542 0.615,0.198 10 false 17 4.865,1.052 5.479,1.25 0.615,0.198 10 false G118 4.969,0.865 5.583,1.063 0.615,0.198 10 false 1 5.26,1.042 5.875,1.24 0.615,0.198 10 false CANH 5.26,1.5 5.875,1.698 0.615,0.198 10 false CANL 4.865,1.5 5.479,1.698 0.615,0.198 10 false G118 4.99,1.302 5.604,1.5 0.615,0.198 10 false 2 4.865,2.25 5.479,2.448 0.615,0.198 10 false G117 5,2.052 5.615,2.25 0.615,0.198 10 false 7 4.865,2.708 5.479,2.906 0.615,0.198 10 false G118 4.854,3.24 5.469,3.438 0.615,0.198 10 false G117 4.979,2.5 5.594,2.698 0.615,0.198 10 false 8 4.99,3.031 5.604,3.229 0.615,0.198 10 false 8 5.25,2.25 5.865,2.448 0.615,0.198 10 false +B 5.26,2.698 5.875,2.896 0.615,0.198 10 false IG1 5.25,3.25 5.865,3.448 0.615,0.198 10 false PGND 4.198,2.125 5.031,2.323 0.833,0.198 10 false PSB 3.802,2.552 4.677,2.75 0.875,0.198 10 false ECU-IG NO.1 2.01,2.698 3.396,2.948 1.385,0.25 10 false from IG1 NO.1 Relay 2.542,2.229 3.375,2.427 0.833,0.198 10 false from Battery 5.125,3.885 6.583,4.198 1.458,0.313 10 false Seat Belt Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (SEAT BELT CONTROL ECU CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (SEAT BELT CONTROL ECU CAN BRANCH WIRE)
a.
U169915E02
2.677,2.719 2.823,2.49 2.823,2.49 2.896,2.49 true 2.573,2.719 2.729,2.146 2.729,2.146 2.813,2.146 true 0.146,0.01 0.365,0.208 0.219,0.198 10 false *a 1.427,2.635 1.813,2.813 0.385,0.177 10 false G118 2.917,2.406 3.344,2.573 0.427,0.167 10 false CANH 2.844,2.063 3.271,2.229 0.427,0.167 10 false CANL

Disconnect the G118 seat belt control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G118-1 (CANH) - G118-2 (CANL) Engine switch off 54 to 64 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Seat Belt Control ECU)



OK

3.CHECK HARNESS AND CONNECTOR (SEAT BELT CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SEAT BELT CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (SEAT BELT CONTROL ECU - BATTERY AND BODY GROUND)
a.
U169967E01
0.06,0.058 0.272,0.248 0.212,0.189 10 *a 1.646,2.932 1.858,3.121 0.212,0.189 10 +B 0.446,3.031 0.868,3.221 0.422,0.189 10 PGND 1.895,3.112 2.143,3.250 0.248,0.138 10 IG1 1.624,3.011 1.561,3.011 1.561,3.011 1.376,2.557 false 0.964,3.11 1.027,3.11 1.027,3.11 1.169,2.557 false 2.197,3.193 2.261,3.193 2.261,3.193 2.353,2.774 false 1.105,0.304 1.489,0.494 0.384,0.189 10 G117 2.34,0.297 2.743,0.486 0.403,0.189 10 G118

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the G117 seat belt control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G117-8 (PGND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G117-7 (+B) - Body ground Always 11 to 14 V
G118-8 (IG1) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Seat Belt Control ECU)


OK

REPLACE SEAT BELT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR