Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U0139  Lost Communication with Suspension Control Module B  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0139 There is no communication from the stabilizer control ECU.
·

Power source or inside stabilizer control ECU

·

Stabilizer control ECU CAN branch wire or connector

·

Stabilizer control ECU



For vehicles with a kinetic dynamic suspension system.


WIRING DIAGRAM

E346816E10
0.573,1.438 1.031,1.635 0.458,0.198 10 false G95 0.542,1.604 2.135,1.958 1.594,0.354 10 false No. 2 Junction Connector 1.906,0.49 2.365,0.688 0.458,0.198 10 false 5 1.917,0.885 2.375,1.083 0.458,0.198 10 false 16 5.542,0.49 6,0.688 0.458,0.198 10 false 29 5.552,0.875 6.01,1.073 0.458,0.198 10 false 28 5.552,1.552 6.01,1.75 0.458,0.198 10 false 24 5.552,2.208 6.01,2.406 0.458,0.198 10 false 22 5.813,0.594 6.271,0.792 0.458,0.198 10 false CANH 5.813,1.031 6.271,1.229 0.458,0.198 10 false CANL 5.813,1.688 6.271,1.885 0.458,0.198 10 false IG 5.792,2.354 6.25,2.552 0.458,0.198 10 false GND 4.677,1.542 5.135,1.74 0.458,0.198 10 false KDSS 2.354,1.677 3.948,2.031 1.594,0.354 10 false from IG1 NO. 3 Relay 5.5,2.729 5.958,2.927 0.458,0.198 10 false G123 5.521,2.896 6.948,3.188 1.427,0.292 10 false Stabilizer Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (STABILIZER CONTROL ECU CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (STABILIZER CONTROL ECU CAN BRANCH WIRE)
a.
U148444E01
1.22,1.569 0.832,1.242 0.832,1.242 0.743,1.242 false 0.25,1.153 0.682,1.301 0.432,0.148 10 CANH 1.302,1.624 0.908,1.942 0.908,1.942 0.818,1.942 false 0.362,1.862 0.794,2.010 0.432,0.148 10 CANL 0.11,0.035 0.542,0.182 0.432,0.148 10 *a 0.236,1.467 0.608,1.614 0.372,0.148 10 G123

Disconnect the G123 stabilizer control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G123-29 (CANH) - G123-28 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Stabilizer Control ECU)



OK

3.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - BATTERY AND GROUND)

NG

REPAIR OR REPLACE STABILIZER CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (STABILIZER CONTROL ECU - BATTERY AND GROUND)
a.
U148445E01
1.814,1.632 2.253,2.011 2.253,2.011 2.325,2.011 false 2.346,1.924 2.698,2.072 0.352,0.148 10 GND 1.645,1.624 1.235,2.027 1.235,2.027 1.161,2.027 false 0.961,1.947 1.131,2.095 0.171,0.148 10 IG 0.11,0.035 0.542,0.182 0.432,0.148 10 *a 0.22,1.388 0.600,1.536 0.380,0.148 10 G123

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G123-22 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G123-24 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Stabilizer Control ECU)


OK

REPLACE STABILIZER CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR