Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261034 CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)  Open in CAN Main Wire  


DESCRIPTION

There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
·

CAN main wire and connector

·

ECM

·

Combination meter assembly

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 3 junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C334433E01
6.126,1.227 6.486,1.403 0.361,0.176 10 ECM 5.706,2.854 6.101,3.030 0.395,0.176 10 G6 5.706,3.014 6.931,3.377 1.225,0.364 10 Combination Meter Assembly 3.108,1.193 3.508,1.369 0.401,0.176 10 G134 3.108,1.352 4.775,1.529 1.667,0.176 10 No. 3 Junction Connector 3.321,2.835 3.722,3.012 0.401,0.176 10 A72 3.321,2.995 4.988,3.171 1.667,0.176 10 No. 1 Junction Connector 1.336,2.842 1.775,3.018 0.439,0.176 10 G132 1.336,3.001 3.136,3.177 1.800,0.176 10 No. 2 Junction Connector 2.513,1.969 2.704,2.123 0.191,0.154 10 8 2.513,2.399 2.707,2.552 0.194,0.153 10 19 4.557,1.969 4.748,2.123 0.191,0.154 10 10 4.557,2.399 4.752,2.552 0.194,0.153 10 21 5.654,1.969 5.829,2.123 0.175,0.154 10 40 5.656,2.399 5.829,2.552 0.173,0.153 10 39 3.361,0.299 3.457,0.452 0.096,0.154 10 1 3.281,0.728 3.456,0.881 0.176,0.153 10 12 2.513,0.299 2.609,0.452 0.096,0.154 10 1 2.513,0.728 2.688,0.881 0.176,0.153 10 12 4.308,0.299 4.404,0.452 0.096,0.154 10 2 4.308,0.728 4.484,0.881 0.176,0.153 10 13 3.616,1.969 3.721,2.123 0.105,0.154 10 9 3.545,2.399 3.721,2.552 0.176,0.153 10 20 5.906,0.285 6.372,0.426 0.466,0.141 10 CANH 5.906,0.932 6.372,1.108 0.466,0.176 10 CANL 5.906,1.975 6.372,2.123 0.466,0.148 10 CANH 5.906,2.579 6.372,2.721 0.466,0.141 10 CANL 0.319,1.191 0.664,1.367 0.345,0.176 10 G48 0.319,1.351 0.738,1.527 0.419,0.176 10 DLC3 0.436,0.385 0.846,0.523 0.410,0.138 10 CANH 0.953,0.3 1.058,0.439 0.105,0.139 10 6 0.953,0.757 1.147,0.896 0.194,0.138 10 14 1.578,0.3 1.674,0.439 0.097,0.139 10 4 1.498,0.757 1.674,0.896 0.175,0.138 10 15 0.456,0.837 0.846,0.975 0.390,0.138 10 CANL 0.155,3.158 1.868,3.312 1.714,0.153 10 *1: for 1KD-FTV 0.164,3.457 1.878,3.610 1.714,0.153 10 *2: for 5L-E 5.466,0.625 5.790,0.779 0.324,0.154 10 36*1 5.461,0.16 5.795,0.314 0.334,0.153 10 35*1 5.473,0.388 5.783,0.527 0.310,0.139 10 G58 5.473,0.845 5.783,0.984 0.310,0.139 10 G58 5.011,0.625 5.335,0.779 0.324,0.154 10 31*2 5.005,0.16 5.340,0.314 0.334,0.153 10 25*2 4.993,0.388 5.352,0.527 0.359,0.139 10 G183 4.993,0.845 5.352,0.984 0.359,0.139 10 G183

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS BRANCH WIRE (NO. 2 JUNCTION CONNECTOR - DLC3)
2.CHECK FOR OPEN IN CAN BUS BRANCH WIRE (NO. 2 JUNCTION CONNECTOR - DLC3)
a.
U170337E01
1.948,2.512 1.763,2.164 1.763,2.164 1.623,2.164 false 1.931,2.959 2.069,3.208 2.069,3.208 2.209,3.208 false 1.916,1.291 2.195,1.649 2.195,1.649 2.293,1.649 false 2.418,0.682 2.303,0.682 2.303,0.682 1.916,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.44,0.605 2.860,0.747 0.420,0.142 10 CANH 2.31,1.564 2.734,1.706 0.424,0.142 10 CANL 2.244,3.14 2.668,3.282 0.424,0.142 10 CANL 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 1.101,2.087 1.521,2.229 0.420,0.142 10 CANH 0.402,1.094 0.763,1.232 0.361,0.138 10 G132

Disconnect the G132 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-4 (CANH) - G48-6 (CANH) Ignition switch off Below 1 Ω
G132-15 (CANL) - G48-14 (CANL) Ignition switch off Below 1 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - ECM)
a.
U170286E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-1 (CANH) - G132-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U170287E01
1.006,0.791 1.107,0.791 1.107,0.791 1.517,1.234 false 1.517,1.439 1.231,1.827 1.231,1.827 1.108,1.827 false 0.497,0.714 0.918,0.851 0.421,0.137 10 CANH 0.625,1.745 1.021,1.882 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.611,1.259 2.968,1.396 0.357,0.137 10 G132

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G132-8 (CANH) - G132-19 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

12.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - ECM)
6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - ECM)
a.
U170288E01
2.516,0.997 2.415,0.997 2.415,0.997 2.169,1.234 false 2.169,1.439 2.388,1.717 2.388,1.717 2.511,1.717 false 2.534,0.92 2.954,1.057 0.421,0.137 10 CANH 2.522,1.635 2.918,1.772 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G134

Disconnect the G134 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-2 (CANH) - G134-13 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)

Result
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 5L-E) C



A

7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

B

8.CONNECT CONNECTOR

C

10.CONNECT CONNECTOR
7.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U170289E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G134

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G134-1 (CANH) - G134-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)
a.
U170369E01
0.08,0.062 0.282,0.291 0.202,0.230 10 *a 0.485,1.077 0.770,1.219 0.286,0.142 10 G58 2.087,1.573 2.2,1.72 2.2,1.72 2.355,1.72 false 2.335,1.976 2.133,1.976 2.133,1.976 1.982,1.573 false 2.383,1.643 2.867,1.785 0.483,0.142 10 CANL 2.36,1.898 2.843,2.040 0.483,0.142 10 CANH

Disconnect the G58 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G58-35 (CANH) - G58-36 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 3 JUNCTION CONNECTOR)

10.CONNECT CONNECTOR
a.

Reconnect the G134 No. 3 junction connector.



NEXT

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)
11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)
a.
U170533E01
0.05,0.057 0.252,0.287 0.202,0.230 10 *a 0.277,1.073 0.643,1.215 0.365,0.142 10 G183 2.641,1.868 2.439,1.868 2.439,1.868 2.257,1.646 false 2.665,1.791 3.149,1.933 0.483,0.142 10 CANL 2.641,1.241 2.439,1.241 2.439,1.241 2.257,1.394 false 2.665,1.164 3.149,1.306 0.483,0.142 10 CANH

Disconnect the G183 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G183-25 (CANH) - G183- 31 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 3 JUNCTION CONNECTOR)

12.CONNECT CONNECTOR
a.

Reconnect the G132 No. 2 junction connector.



NEXT

13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
13.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U148889E01
1.006,0.963 1.107,0.963 1.107,0.963 1.31,1.234 false 1.31,1.439 1.171,1.699 1.171,1.699 1.048,1.699 false 0.497,0.886 0.918,1.022 0.421,0.137 10 CANH 0.565,1.618 0.961,1.755 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A72

Disconnect the A72 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-10 (CANH) - A72-21 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

NG

15.CONNECT CONNECTOR
14.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U148890E01
1.032,0.862 1.133,0.862 1.133,0.862 1.414,1.234 false 1.414,1.439 1.227,1.755 1.227,1.755 1.104,1.755 false 0.523,0.784 0.944,0.921 0.421,0.137 10 CANH 0.621,1.674 1.017,1.810 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-9 (CANH) - A72-20 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

15.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

16.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)
16.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)
a.
U148233E01
0.723,0.39 0.931,0.530 0.208,0.139 10 G6 1.935,0.186 2.374,0.322 0.440,0.137 10 CANH 1.724,0.437 2.163,0.574 0.440,0.137 10 CANL 0.074,0.063 0.404,0.245 0.330,0.183 10 *a 2.938,1.372 2.609,0.275 2.609,0.275 2.454,0.275 false 2.809,1.369 2.375,0.514 2.375,0.514 2.221,0.514 false

Disconnect the G6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 1 JUNCTION CONNECTOR)