Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261040 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69040A 1.INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

B184438E24
5.75,1.833 6.167,2.031 false 5.01,1.833 4.583,2.052 false 5.292,2.063 5.229,2.396 false 5.448,2.052 5.635,2.417 false 2,2.333 2.375,2.5 0.375,0.167 10 false *a 2.5,2 3.01,2.177 0.51,0.177 10 false *b 4.104,0.615 4.531,0.865 0.427,0.25 10 false *c 4.458,1.979 4.667,2.167 0.208,0.188 10 false L 6.25,1.99 6.552,2.333 0.302,0.344 10 false UL 5.667,2.417 5.906,2.635 0.24,0.219 10 false E 5,2.417 5.469,2.677 0.469,0.26 10 false LSSR

Text in Illustration
*a Lock *b Unlock
*c Component without harness connected
(Front Door Lock Assembly LH)
- -

a.

Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the front door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (LSSR) - 7 (E) Lock 10 kΩ or higher
8 (LSSR) - 7 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly.




c.

for LHD:

B184437E15
2.551,0.8 2.971,0.970 0.420,0.170 10 *a 2.266,1.946 2.773,2.126 0.507,0.180 10 *c 2.84,1.511 3.149,1.665 0.310,0.155 10 *b 4.442,0.807 4.712,1.108 0.270,0.301 10 *d 5.315,2.347 5.446,2.528 0.131,0.180 10 E 4.482,2.251 4.723,2.404 0.240,0.153 10 UL 5.043,2.347 5.208,2.490 0.164,0.142 10 L 5.365,2.084 5.365,2.34 false 5.077,2.089 5.077,2.34 false 4.913,2.084 4.651,2.294 false

Text in Illustration
*a Lock *b Off
*c Unlock *d Component without harness connected
(Front Door Lock Assembly LH)

i.

Check the door lock and unlock switch.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E)
10 (UL) - 7 (E)
OFF 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω



If the result is not as specified, replace the front door lock assembly.




Hide 69040A 2.INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

B144111E16
5.073,1.885 4.667,2.083 false 5.531,2.01 5.667,2.333 false 5.333,2.052 5.302,2.333 false 5.292,1.833 4.667,1.5 false 5.75,1.833 6.094,1.833 false 5.583,1.833 6.021,1.396 false 2.042,2.333 2.417,2.5 0.375,0.167 10 false *a 2.5,1.906 3.01,2.083 0.51,0.177 10 false *b 4.385,0.635 4.677,0.906 0.292,0.271 10 false *c 4.5,2.063 4.708,2.25 0.208,0.188 10 false U 4.448,1.417 4.75,1.594 0.302,0.177 10 false UL 5.667,2.333 5.833,2.583 0.167,0.25 10 false E 5.104,2.333 5.5,2.531 0.396,0.198 10 false LSSR 6.135,1.75 6.583,1.938 0.448,0.188 10 false UNDL 6.104,1.302 6.417,1.5 0.313,0.198 10 false DL

Text in Illustration
*a Lock *b Unlock
*c Component without harness connected
(Front Door Lock Assembly LH)
- -

a.

Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 3 (UL)
Lock
Battery positive (+) → 3 (UL)
Battery negative (-) → 4 (L)
Unlock
Battery positive (+) → 2 (DL)
Battery negative (-) → 1 (UNDL)
Set
Battery positive (+) → 1 (UNDL)
Battery negative (-) → 2 (DL)
Unset


If the result is not as specified, replace the front door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (LSSR) - 7 (E) Lock 10 kΩ or higher
8 (LSSR) - 7 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly.




c.

for LHD:

B144108E03
4.513,0.856 5.096,1.180 0.583,0.325 10 *c 4.642,2.383 4.875,2.551 0.232,0.168 10 UL 5.133,2.383 5.365,2.551 0.232,0.168 10 L 5.588,2.383 5.820,2.551 0.232,0.168 10 E 4.988,2.088 4.744,2.366 false 5.161,2.362 5.177,2.082 false 5.455,2.04 5.616,2.362 false 3.199,1.307 3.682,1.484 0.482,0.177 10 *b 3.385,0.57 3.867,0.747 0.482,0.177 10 *a

Text in Illustration
*a Lock *b Unlock
*c Component without harness connected
(Front Door Lock Assembly LH)
- -

i.

Check the door lock and unlock switch.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E)
10 (UL) - 7 (E)
OFF 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω



If the result is not as specified, replace the front door lock assembly.




Hide 69030A 3.INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

B184439E26
5.167,2 5.01,2.354 false 5.354,2 5.583,2.365 false 4.917,1.802 4.365,1.917 false 5.677,1.792 6.083,1.917 false 1.25,2.063 1.833,2.25 0.583,0.188 10 false *a 1.833,2.333 2.188,2.583 0.354,0.25 10 false *b 4.458,0.74 4.813,1.052 0.354,0.313 10 false *c 5.469,2.427 5.917,2.667 0.448,0.24 10 false LSSR 4.938,2.417 5.083,2.615 0.146,0.198 10 false E 4.25,1.833 4.698,2.167 0.448,0.333 10 false L 6.156,1.833 6.667,2.177 0.51,0.344 10 false UL

Text in Illustration
*a Unlock *b Lock
*c Component without harness connected
(Front Door Lock Assembly RH)
- -

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly.




c.

for RHD:

B144104E08
4.451,0.743 4.836,1.019 0.385,0.275 10 *c 5.965,2.369 6.198,2.537 0.232,0.168 10 UL 5.592,2.369 5.824,2.537 0.232,0.168 10 L 5.137,2.369 5.369,2.537 0.232,0.168 10 E 1.369,0.625 1.851,0.802 0.482,0.177 10 *a 1.159,1.375 1.641,1.551 0.482,0.177 10 *b 5.306,2.074 5.198,2.344 false 5.613,2.078 5.638,2.369 false 5.761,2.084 6.013,2.336 false

Text in Illustration
*a Unlock *b Lock
*c Component without harness connected
(Front Door Lock Assembly RH)
- -

i.

Check the door lock and unlock switch.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (L) - 8 (E) Lock Below 1 Ω
6 (L) - 8 (E)
5 (UL) - 8 (E)
OFF 10 kΩ or higher
5 (UL) - 8 (E) Unlock Below 1 Ω



If the result is not as specified, replace the front door lock assembly.




Hide 69030A 4.INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

B144110E13
5.802,1.865 6.25,2.083 false 5.583,1.833 6.073,1.427 false 5.5,2.083 5.604,2.417 false 5.333,2.073 5.135,2.417 false 5.292,1.833 4.75,1.333 false 5.01,1.917 4.5,2.24 false 1.625,2.281 2,2.448 0.375,0.167 10 false *b 1.156,1.917 1.667,2.094 0.51,0.177 10 false *a 4.229,0.563 4.573,0.844 0.344,0.281 10 false *c 6.125,1.313 6.333,1.5 0.208,0.188 10 false L 6.333,2.073 6.635,2.25 0.302,0.177 10 false UL 5.5,2.427 5.896,2.667 0.396,0.24 10 false LSSR 5.063,2.417 5.25,2.625 0.188,0.208 10 false E 4.302,2.167 4.583,2.333 0.281,0.167 10 false DL 4.375,1.219 4.833,1.417 0.458,0.198 10 false UNDL

Text in Illustration
*a Unlock *b Lock
*c Component without harness connected
(Front Door Lock Assembly RH)
- -

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 2 (L)
Unlock
Battery positive (+) → 4 (DL)
Battery negative (-) → 3 (UNDL)
Set
Battery positive (+) → 3 (UNDL)
Battery negative (-) → 4 (DL)
Unset


If the result is not as specified, replace the front door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly.




c.

for RHD:

B144105E05
4.568,0.786 4.881,1.044 0.313,0.258 10 *c 5.796,2.369 6.028,2.537 0.232,0.168 10 UL 5.54,2.369 5.773,2.537 0.232,0.168 10 L 4.976,2.369 5.209,2.537 0.232,0.168 10 E 5.251,2.094 5.011,2.352 false 5.568,2.348 5.568,2.096 false 5.752,2.082 5.873,2.348 false 1.355,0.611 1.837,0.788 0.482,0.177 10 *a 1.159,1.403 1.641,1.579 0.482,0.177 10 *b

Text in Illustration
*a Unlock *b Lock
*c Component without harness connected
(Front Door Lock Assembly RH)
- -

i.

Check the door lock and unlock switch.

1.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (L) - 8 (E) Lock Below 1 Ω
6 (L) - 8 (E)
5 (UL) - 8 (E)
OFF 10 kΩ or higher
5 (UL) - 8 (E) Unlock Below 1 Ω



If the result is not as specified, replace the front door lock assembly.