Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261041 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69060A 1.INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

B184440E12
5.698,1.823 6.167,2.083 false 4.99,1.833 4.5,2.083 false 5.083,2 4.917,2.333 false 5.583,2 5.667,2.313 false 1.781,2.177 2.271,2.344 0.49,0.167 10 false *b 1.115,2.042 1.51,2.229 0.396,0.188 10 false *a 4.5,0.865 4.854,1.073 0.354,0.208 10 false *c 6.25,2 6.5,2.188 0.25,0.188 10 false UL 4.385,2 4.583,2.198 0.198,0.198 10 false L 5.5,2.344 5.938,2.583 0.438,0.24 10 false LSSR 4.833,2.375 5,2.583 0.167,0.208 10 false E

Text in Illustration
*a Lock *b Unlock
*c Component without harness connected
(Rear Door Lock assembly LH)
- -

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the rear door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Unlock Below 1 Ω
6 (LSSR) - 9 (E) Lock 10 kΩ or higher


If the result is not as specified, replace the rear door lock assembly.




Hide 69340 2.INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

B144119E08
1.882,2.1 2.374,2.263 0.492,0.163 10 *b 1.312,2.093 1.709,2.277 0.397,0.184 10 *a 4.244,0.672 4.714,0.936 0.470,0.263 10 *c 6.026,1.868 6.279,2.056 0.253,0.188 10 UL 5.973,1.404 6.166,1.597 0.193,0.193 10 L 5.554,1.834 6.011,1.918 false 5.357,1.796 5.932,1.502 false 5.95,2.237 6.434,2.497 0.485,0.260 10 LSSR 5.432,2.335 5.597,2.514 0.165,0.179 10 E 5.445,2.007 5.481,2.307 false 5.582,2.004 5.929,2.291 false 4.064,1.207 4.557,1.405 0.493,0.198 10 UNDL 4.162,1.953 4.405,2.119 0.243,0.166 10 DL 5.038,1.757 4.467,1.27 false 4.81,1.778 4.39,2.006 false

Text in Illustration
*a Lock *b Unlock
*c Component without harness connected
(Rear Door Lock Assembly LH)
- -

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 2 (L)
Unlock
Battery positive (+) → 4 (DL)
Battery negative (-) → 3 (UNDL)
Set
Battery positive (+) → 3 (UNDL)
Battery negative (-) → 4 (DL)
Unset


If the result is not as specified, replace the rear door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (LSSR) - 6 (E) Unlock Below 1 Ω
5 (LSSR) - 6 (E) Lock 10 kΩ or higher


If the result is not as specified, replace the rear door lock assembly.




Hide 69330 3.INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

B184441E13
5.833,1.833 6.281,1.99 false 5.031,1.833 4.583,1.99 false 5.667,2.01 5.76,2.333 false 5.177,2 5.083,2.323 false 2.396,2.094 2.75,2.25 0.354,0.156 10 false *b 1.771,2.25 2.25,2.406 0.479,0.156 10 false *a 4.594,0.74 4.969,1.021 0.375,0.281 10 false *c 6.333,1.906 6.583,2.083 0.25,0.177 10 false UL 4.5,1.917 4.74,2.073 0.24,0.156 10 false L 5.625,2.333 6.083,2.594 0.458,0.26 10 false LSSR 5.01,2.333 5.167,2.531 0.156,0.198 10 false E

Text in Illustration
*a Unlock *b Lock
*c Component without harness connected
(Rear Door Lock Assembly RH)
- -

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the rear door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (LSSR) - 9 (E) Unlock Below 1 Ω
6 (LSSR) - 9 (E) Lock 10 kΩ or higher


If the result is not as specified, replace the rear door lock assembly.




Hide 69330 4.INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

B144120E10
4.833,1.854 4.25,2.083 false 5.979,2.125 5.5,1.833 false 5,2.042 5.219,2.417 false 4.823,2.052 4.667,2.417 false 5,1.833 4.333,1.385 false 5.333,1.833 6,1.25 false 4.229,0.708 4.542,0.979 0.313,0.271 10 false *c 4.156,2 4.333,2.198 0.177,0.198 10 false L 4.125,1.292 4.396,1.469 0.271,0.177 10 false UL 2,2.104 2.25,2.333 0.25,0.229 10 false *b 1.417,2.104 1.688,2.333 0.271,0.229 10 false *a 5.052,2.469 5.5,2.667 0.448,0.198 10 false LSSR 4.583,2.448 4.854,2.667 0.271,0.219 10 false E 6.063,2.052 6.583,2.333 0.521,0.281 10 false UNDL 6.021,1.156 6.302,1.333 0.281,0.177 10 false DL

Text in Illustration
*a Unlock *b Lock
*c Component without harness connected
(Rear Door Lock Assembly RH)
- -

a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 3 (UL)
Lock
Battery positive (+) → 3 (UL)
Battery negative (-) → 4 (L)
Unlock
Battery positive (+) → 2 (DL)
Battery negative (-) → 1 (UNDL)
Set
Battery positive (+) → 1 (UNDL)
Battery negative (-) → 2 (DL)
Unset


If the result is not as specified, replace the rear door lock assembly.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (LSSR) - 10 (E) Unlock Below 1 Ω
9 (LSSR) - 10 (E) Lock 10 kΩ or higher


If the result is not as specified, replace the rear door lock assembly.