Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL TRANSMITTER(w/o Entry and Start System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261046 DOOR CONTROL TRANSMITTER(w/o Entry and Start System) G

DOOR LOCK  DOOR CONTROL TRANSMITTER(w/o Entry and Start System)  INSPECTION  


PROCEDURE

Hide 89071B 1.INSPECT DOOR CONTROL TRANSMITTER MODULE (except Separate Type)

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.


a.

Inspect the operation of the transmitter.

i.

Remove the battery (lithium battery) from the transmitter (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Entry and Start System)>REMOVAL).


ii.
B185421

Install a new or normal battery (lithium battery).

HINT:

When a new or normal battery is not available, first connect 2 new 1.5 V batteries in series. Then connect leads to the batteries and apply 3 V to the transmitter shown in the illustration.



iii.

From outside the vehicle, approximately 1 m (3.28 ft) from the driver side outside door handle, test the transmitter by pointing its key plate at the vehicle and pressing a transmitter switch.

OK:

The door lock can be operated via the transmitter.

The LED comes on more than once.


·

The operational area differs depending on the user, the way the transmitter is held and the location.

·

The weak electric waves from the transmitter may be affected if the area has strong electric waves or noise. The transmitter operational area may be reduced or the transmitter may not function.




b.

Inspect the battery capacity.

i.

Remove the battery from the electrical key transmitter that does not operate (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Entry and Start System)>REMOVAL).


ii.

Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between the terminals or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.



iii.
B178438

Carefully extend the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iv.
B359150E02
2.917,0.917 2.531,0.917 false 2.979,0.833 3.25,1.031 0.271,0.198 10 false *a

Check the transmitter battery voltage.

HINT:

Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter module set sub-assembly.


Text in Illustration
*a GND

Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Ignition switch off, all doors closed and lock or unlock switch is pressed 2.5 to 3.2 V


If the result is not as specified, replace the transmitter battery.



Hide 89745A 2.INSPECT TRANSMITTER BATTERY (for Separate Type)

NOTICE:

When replacing the transmitter battery, before starting work, remove static electricity that has built up in the body by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.


a.

Inspect the operation of the transmitter.

i.

Remove the battery (lithium battery) from the transmitter (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Entry and Start System)>REMOVAL).


ii.
B239793

Install a new or normal battery (lithium battery).

HINT:

If a new or normal battery is not available, first connect 2 new 1.5 V batteries in series. Then connect leads to the batteries and apply 3 V to the transmitter shown in the illustration.



iii.

From outside the vehicle, approximately 1 m (3.28 ft) away from the driver side outside door handle, test the transmitter by pointing its key plate at the vehicle and pressing a transmitter switch, or while carrying the transmitter, touch the inside of the handle and pull it.

OK:

The door lock can be operated via the transmitter.

The LED comes on more than once.


HINT:
·

The operational area differs depending on the user, the way the transmitter is held and the location.

·

The weak electric waves from the transmitter may be affected if the area has strong electric waves or noise. The transmitter operational area may be reduced or the transmitter may not function.





b.
B239794

Inspect the battery capacity.

i.

Remove the battery from the electrical key transmitter that does not operate (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/o Entry and Start System)>REMOVAL).


ii.

Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.



iii.

Carefully extend the lead wire from the position shown in the illustration and install the previously removed transmitter battery.


iv.
B359151E01
1.923,1.001 2.293,0.769 2.293,0.769 2.529,0.769 false 2.55,0.675 2.866,0.865 0.316,0.191 10 *a

Check the transmitter battery voltage.

HINT:

Measure the transmitter battery voltage while pressing the lock or unlock switch on the door control transmitter module set sub-assembly.


Text in Illustration
*a GND

Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Ignition switch off, all doors closed and lock or unlock switch is pressed 2.5 to 3.2 V


If the result is not as specified, replace the transmitter battery.