Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Unlock Function does not Operate  


DESCRIPTION

If the back door entry unlock function does not operate but the back door lock function operates, the communication line between the vehicle and electrical key transmitter is normal. The entry unlock switch circuit (luggage electrical key switch → certification ECU) may be faulty.

WIRING DIAGRAM

B242195E04
1.27,1.448 3.196,1.760 1.925,0.312 10 Luggage Electrical Key Switch (Unlock Switch) 1.27,1.29 1.601,1.429 0.330,0.138 10 X6 4.962,1.659 6.062,1.838 1.100,0.179 10 Certification ECU 4.962,1.528 5.283,1.667 0.321,0.139 10 G38 4.669,0.882 5.121,1.027 0.452,0.145 10 TSW5 2.847,0.795 2.944,0.941 0.097,0.147 10 5 2.558,0.795 2.768,0.941 0.210,0.147 10 UL 1.614,0.794 1.854,0.945 0.240,0.152 10 E 1.433,0.795 1.531,0.941 0.098,0.147 10 6 4.399,0.775 4.591,0.921 0.192,0.147 10 22

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitters in the vehicle.

·

When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

·

Before replacing the certification ECU, refer to the Service Bulletin.



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)

NG

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Lock Pos SW Back door lock position switch status / ON or OFF ON: Back door unlocked
OFF: Back door locked
-

OK:

On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.




OK

3.READ VALUE USING INTELLIGENT TESTER (UNLOCK SWITCH)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Back Door Lock/Unlock Functions do not Operate)

3.READ VALUE USING INTELLIGENT TESTER (UNLOCK SWITCH)
a.

Using the intelligent tester, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Tr/B Door Unlock SW Back door unlock switch / ON or OFF ON: Back door unlock switch pushed
OFF: Back door unlock switch not pushed
-

OK:

"ON" (unlock switch is pushed) and "OFF" (unlock switch is not pushed) appear on the screen.




OK

REPLACE CERTIFICATION ECU

NG

4.INSPECT LUGGAGE ELECTRICAL KEY SWITCH (UNLOCK SWITCH)
4.INSPECT LUGGAGE ELECTRICAL KEY SWITCH (UNLOCK SWITCH)
a.

E139345E13
2.458,1.67 1.985,1.476 false 2.458,1.67 1.985,1.476 false 2.486,1.597 2.791,1.787 0.305,0.190 10 E 1.661,1.469 1.156,1.67 false 0.91,1.599 1.121,1.778 0.211,0.179 10 UL

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (UL) - 6 (E) No switch pushed 10 kΩ or higher
5 (UL) - 6 (E) Unlock switch pushed Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (LUGGAGE ELECTRICAL KEY SWITCH - CERTIFICATION ECU)

NG

5.CHECK HARNESS AND CONNECTOR (LUGGAGE ELECTRICAL KEY SWITCH - CERTIFICATION ECU)
a.

Disconnect the X6 switch connector.


b.

Disconnect the G38 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X6-5 (UL) - G38-22 (TSW5) Always Below 1 Ω
G38-22 (TSW5) - Body ground Always 10 kΩ or higher
X6-6 (E) - Body ground Always Below 1 Ω




OK

REPLACE CERTIFICATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR