If the back door entry lock function does not operate but the back door unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The entry lock switch circuit (luggage electrical key switch → certification ECU) may be faulty.
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Check that there are no electrical key transmitters in the vehicle.
When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
Before replacing the certification ECU, refer to the Service Bulletin.
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Back Door Lock Pos SW | Back door lock position switch status / ON or OFF | ON: Back door unlocked
OFF: Back door locked |
- |
On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
OK
NG
Using the intelligent tester, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Tr/B-Door Lock SW | Back door lock switch / ON or OFF | ON: Back door lock switch pushed
OFF: Back door lock switch not pushed |
- |
"ON" (lock switch is pushed) and "OFF" (lock switch is not pushed) appear on the screen.
OK
NG
Remove the luggage electrical key switch (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 2 (L) - 3 (B) | No switch pushed | 10 kΩ or higher |
| 2 (L) - 3 (B) | Lock switch pushed | Below 1 Ω |
OK
NG
Disconnect the X6 switch connector.
Disconnect the G38 ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X6-2 (L) - G38-23 (TSW6) | Always | Below 1 Ω |
| G38-23 (TSW6) - Body ground | Always | 10 kΩ or higher |
| X6-3 (B) - Body ground | Always | Below 1 Ω |
OK
NG