Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

When the back door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) the power door lock control system, 2) the electrical key antenna (outside luggage) or 3) the certification ECU.

WIRING DIAGRAM

B210706E05
0.369,2.055 0.669,2.215 0.299,0.160 10 R16 1.537,0.691 1.939,0.834 0.402,0.142 10 CLG5 1.532,1.558 1.939,1.719 0.406,0.160 10 CLGB 2.024,0.588 2.229,0.757 0.205,0.169 10 1 2.034,1.468 2.194,1.615 0.160,0.147 10 2 4.761,0.601 4.957,0.757 0.196,0.156 10 19 5.028,0.685 5.425,0.834 0.398,0.149 10 CLG8 5.036,1.547 5.465,1.714 0.429,0.167 10 CG8B 4.766,1.455 4.948,1.615 0.183,0.160 10 20 4.976,2.076 5.268,2.238 0.292,0.162 10 G39 4.976,2.225 6.107,2.386 1.132,0.161 10 Certification ECU 0.37,2.211 2.986,2.390 2.617,0.180 10 Electrical Key Antenna (Outside Luggage)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitters in the vehicle.

·

When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

·

Before replacing the certification ECU, refer to the Service Bulletin.



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.CHECK WAVE ENVIRONMENT

NG

2.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage) and perform an entry back door unlock function check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not possible.


HINT:

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.


OK:

Entry function operates normally.




OK

AFFECTED BY WAVE INTERFERENCE

NG

3.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
3.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Back Door Lock Pos SW Back door lock position switch status / ON or OFF ON: Back door unlocked
OFF: Back door locked
-

OK:

On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.




OK

4.CHECK ELECTRICAL KEY ANTENNA IN KEY DIAGNOSTIC MODE

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Back Door Lock/Unlock Functions do not Operate)

4.CHECK ELECTRICAL KEY ANTENNA IN KEY DIAGNOSTIC MODE
a.

Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).

i.

Check the electrical key antenna (outside luggage).

When the electrical key transmitter is brought within 0.7 to 1.0 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.





OK

REPLACE CERTIFICATION ECU

NG

5.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
5.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the R16 antenna connector.


b.

Disconnect the G39 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R16-1 (CLG5) - G39-19 (CLG8) Always Below 1 Ω
R16-2 (CLGB) - G39-20 (CG8B) Always Below 1 Ω
G39-19 (CLG8) - Body ground Always 10 kΩ or higher
G39-20 (CG8B) - Body ground Always 10 kΩ or higher




OK

6.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
a.
B226391E01
1.827,1.07 2.303,0.72 false 1.581,1.07 1.037,0.743 false 2.36,0.617 2.784,0.791 0.424,0.174 10 CLGB 0.555,0.623 0.980,0.797 0.424,0.174 10 CLG5

Remove the electrical key antenna (outside luggage) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Outside Luggage Compartment)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (CLG5) - 2 (CLGB) Always Below 1 Ω




OK

REPLACE CERTIFICATION ECU

NG