Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A6  Open in Rear Floor Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the indoor No. 2 electrical key antenna (rear floor). The indoor No. 2 electrical key antenna (rear floor) detects that the electrical key is inside the vehicle and transmits the request signal received from the certification ECU. DTC B27A6 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and indoor No. 2 electrical key antenna (rear floor) (CLG6 - CLG4, CG6B - CLGB).

DTC Code DTC Detection Condition Trouble Area
B27A6 An open circuit is detected in the circuit between the certification ECU and indoor No. 2 electrical key antenna (rear floor) (CLG6 - CLG4, CG6B - CLGB).
·

Harness or connector

·

Indoor No. 2 electrical key antenna (rear floor)

·

Certification ECU



WIRING DIAGRAM

B243942E01
0.329,1.489 1.295,1.659 0.965,0.170 10 R14*1, s1*2 0.329,1.644 3.995,1.818 3.666,0.174 10 Indoor No. 2 Electrical Key Antenna Assembly (Rear Floor) 0.329,2.009 1.310,2.182 0.980,0.174 10 *1: for 5 Door 0.329,2.348 1.310,2.521 0.980,0.174 10 *2: for 3 Door 1.592,0.953 2.002,1.113 0.410,0.160 10 CLGB 1.613,0.439 2.014,0.591 0.402,0.152 10 CLG4 5.116,0.448 5.510,0.608 0.393,0.160 10 CLG6 5.108,0.945 5.520,1.097 0.413,0.152 10 CG6B 6.092,0.955 6.228,1.115 0.136,0.160 10 E 6.303,0.863 6.499,1.036 0.196,0.173 10 15 4.831,0.862 5.010,1.002 0.179,0.140 10 25 4.853,0.356 5.025,0.517 0.172,0.161 10 24 2.1,0.858 2.215,1.010 0.115,0.152 10 2 2.096,0.336 2.215,0.500 0.119,0.164 10 1 5.095,1.469 5.403,1.619 0.308,0.150 10 G38 5.095,1.623 6.253,1.776 1.158,0.153 10 Certification ECU

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU, refer to the Service Bulletin.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU and indoor No. 2 electrical key antenna (rear floor).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (INDOOR NO. 2 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (INDOOR NO. 2 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the R14*1 or s1*2 antenna connector.

*1: for 5 Door

*2: for 3 Door



b.

Disconnect the G38 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Door
Tester Connection Condition Specified Condition
R14-1 (CLG4) - G38-24 (CLG6) Always Below 1 Ω
R14-2 (CLGB) - G38-25 (CG6B) Always Below 1 Ω
G38-24 (CLG6) - Body ground Always 10 kΩ or higher
G38-25 (CG6B) - Body ground Always 10 kΩ or higher
G38-15 (E) - Body ground Always Below 1 Ω

for 3 Door
Tester Connection Condition Specified Condition
s1-1 (CLG4) - G38-24 (CLG6) Always Below 1 Ω
s1-2 (CLGB) - G38-25 (CG6B) Always Below 1 Ω
G38-24 (CLG6) - Body ground Always 10 kΩ or higher
G38-25 (CG6B) - Body ground Always 10 kΩ or higher
G38-15 (E) - Body ground Always Below 1 Ω




OK

3.CHECK CERTIFICATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU
a.

Measure the voltage according to the value(s) in the table below.

U169660E01
1.025,0.173 1.241,0.384 0.217,0.212 10 *a 1.647,0.443 1.944,0.622 0.297,0.179 10 G38 3.045,0.467 3.461,0.631 0.416,0.165 10 CLG6 2.201,0.47 2.644,0.642 0.443,0.172 10 CG6B 2.729,1.261 2.609,0.533 false 0.896,0.701 1.054,0.872 0.158,0.172 10 E 1.482,1.143 1.017,0.763 false 3.007,0.538 2.846,1.263 false

Text in Illustration
*a Component with harness connected
(Certification ECU)
- -

OK:
Tester Connection Switch Condition Specified Condition
G38-24 (CLG6) - G38-15 (E) Engine switch off, all doors closed, key not in cabin and lock sensor off → on No pulse generation → Pulse generation
G38-25 (CG6B) - G38-15 (E) Engine switch off, all doors closed, key not in cabin and lock sensor off → on No pulse generation → Pulse generation




OK

4.REPLACE INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU

4.REPLACE INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
a.

Temporarily replace the indoor No. 2 electrical key antenna (rear floor) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Rear Floor)>REMOVAL).



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

OK

END (INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU