Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A7  Open in Inside Luggage Compartment Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the indoor No. 3 electrical key antenna (inside luggage). The indoor No. 3 electrical key antenna (inside luggage) detects that the electrical key is inside the vehicle and transmits the request signal received from the certification ECU. DTC B27A7 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and indoor No. 3 electrical key antenna (inside luggage) (CLG7 - CLG6, CG7B - CLGB).

DTC Code DTC Detection Condition Trouble Area
B27A7 An open circuit is detected in the circuit between the certification ECU and indoor No. 3 electrical key antenna (inside luggage) (CLG7 - CLG6, CG7B - CLGB).
·

Harness or connector

·

Indoor No. 3 electrical key antenna (inside luggage)

·

Certification ECU



WIRING DIAGRAM

B210705E15
0.444,1.94 0.740,2.110 0.295,0.170 10 R15 0.444,2.095 2.691,2.426 2.246,0.331 10 Indoor No. 3 Electrical Key Antenna Assembly (Inside Luggage) 1.509,1.558 1.919,1.718 0.410,0.160 10 CLGB 1.53,0.687 1.931,0.839 0.402,0.152 10 CLG6 5.033,0.695 5.426,0.856 0.393,0.160 10 CLG7 5.024,1.551 5.437,1.703 0.413,0.152 10 CG7B 6.009,1.56 6.144,1.721 0.136,0.160 10 E 6.22,1.468 6.415,1.642 0.196,0.173 10 15 4.747,1.467 4.926,1.607 0.179,0.140 10 27 4.782,0.612 4.954,0.773 0.172,0.161 10 26 2.017,1.463 2.132,1.615 0.115,0.152 10 2 2.012,0.584 2.132,0.748 0.119,0.164 10 1 5.012,2.062 5.320,2.212 0.308,0.150 10 G38 5.012,2.217 6.170,2.369 1.158,0.153 10 Certification ECU

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU, refer to the Service Bulletin.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU and indoor No. 3 electrical key antenna (inside luggage).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (INDOOR NO. 3 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (INDOOR NO. 3 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the R15 antenna connector.


b.

Disconnect the G38 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R15-1 (CLG6) - G38-26 (CLG7) Always Below 1 Ω
R15-2 (CLGB) - G38-27 (CG7B) Always Below 1 Ω
G38-26 (CLG7) - Body ground Always 10 kΩ or higher
G38-27 (CG7B) - Body ground Always 10 kΩ or higher
G38-15 (E) - Body ground Always Below 1 Ω




OK

3.CHECK CERTIFICATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU
a.

Measure the voltage according to the value(s) in the table below.

U169661E01
1.025,0.173 1.241,0.384 0.217,0.212 10 *a 2.411,0.248 2.708,0.427 0.297,0.179 10 G38 2.818,0.463 3.234,0.628 0.416,0.165 10 CLG7 1.974,0.466 2.417,0.638 0.443,0.172 10 CG7B 2.502,1.257 2.382,0.529 false 0.896,0.701 1.054,0.872 0.158,0.172 10 E 1.482,1.143 1.017,0.763 false 2.78,0.534 2.619,1.259 false

Text in Illustration
*a Component with harness connected
(Certification ECU)
- -

OK:
Tester Connection Switch Condition Specified Condition
G38-26 (CLG7) - G38-15 (E) Engine switch off, all doors closed, key not in cabin and lock sensor off → on No pulse generation → Pulse generation
G38-27 (CG7B) - G38-15 (E) Engine switch off, all doors closed, key not in cabin and lock sensor off → on No pulse generation → Pulse generation




OK

4.REPLACE INDOOR NO. 3 ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)

NG

REPLACE CERTIFICATION ECU

4.REPLACE INDOOR NO. 3 ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)
a.

Temporarily replace the indoor No. 3 electrical key antenna (inside luggage) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Luggage Compartment)>REMOVAL).



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

OK

END (INDOOR NO. 3 ELECTRICAL KEY ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU