Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A8  Open in Outside Luggage Compartment Electrical Key Antenna Circuit  


DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the electrical key antenna (outside luggage). The electrical key antenna (outside luggage) detects that the electrical key is brought close to the vehicle, and when a request signal is received from within 1.0 m (3.28 ft.) of the back door, the signal is transmitted. DTC B27A8 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB).

DTC Code DTC Detection Condition Trouble Area
B27A8 An open circuit is detected in the circuit between the certification ECU and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB).
·

Harness or connector

·

Electrical key antenna (outside luggage)

·

Certification ECU



WIRING DIAGRAM

B210706E05
0.369,2.055 0.669,2.215 0.299,0.160 10 R16 1.537,0.691 1.939,0.834 0.402,0.142 10 CLG5 1.532,1.558 1.939,1.719 0.406,0.160 10 CLGB 2.024,0.588 2.229,0.757 0.205,0.169 10 1 2.034,1.468 2.194,1.615 0.160,0.147 10 2 4.761,0.601 4.957,0.757 0.196,0.156 10 19 5.028,0.685 5.425,0.834 0.398,0.149 10 CLG8 5.036,1.547 5.465,1.714 0.429,0.167 10 CG8B 4.766,1.455 4.948,1.615 0.183,0.160 10 20 4.976,2.076 5.268,2.238 0.292,0.162 10 G39 4.976,2.225 6.107,2.386 1.132,0.161 10 Certification ECU 0.37,2.211 2.986,2.390 2.617,0.180 10 Electrical Key Antenna (Outside Luggage)

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU, refer to the Service Bulletin.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU and electrical key antenna (outside luggage).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the R16 antenna connector.


b.

Disconnect the G39 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R16-1 (CLG5) - G39-19 (CLG8) Always Below 1 Ω
R16-2 (CLGB) - G39-20 (CG8B) Always Below 1 Ω
G39-19 (CLG8) - Body ground Always 10 kΩ or higher
G39-20 (CG8B) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
a.

B226391E01
1.827,1.07 2.303,0.72 false 1.581,1.07 1.037,0.743 false 2.36,0.617 2.784,0.791 0.424,0.174 10 CLGB 0.555,0.623 0.980,0.797 0.424,0.174 10 CLG5

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (CLG5) - 2 (CLGB) Always Below 1 Ω




OK

4.REPLACE CERTIFICATION ECU

NG

4.REPLACE CERTIFICATION ECU
a.

Temporarily replace the certification ECU with a new one (Refer to the Service Bulletin).



NEXT

5.CHECK FOR DTC