Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  TERMINALS OF ECU  


CHECK ENGINE SWITCH


U169631E02
3.469,0.146 3.781,0.292 0.313,0.146 10 false G36

a.

Disconnect the G36 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G36-8 (AGND) - Body ground GR - Body ground Ground Always Below 1 Ω
G36-5 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the G36 switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G36-9 (TXCT) - G36-8 (AGND) W - GR Key code output signal Engine switch off, 30 seconds or more after door opened or closed and brake pedal*1 or clutch pedal*2 not depressed Below 1 V
G36-9 (TXCT) - G36-8 (AGND) W - GR Key code output signal Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed Pulse generation
(see waveform 1)
G36-10 (CODE) - G36-8 (AGND) V - GR Demodulated signal of key code data Engine switch off, 30 seconds or more after door opened or closed and brake pedal*1 or clutch pedal*2 not depressed Below 1 V
G36-10 (CODE) - G36-8 (AGND) V - GR Demodulated signal of key code data Engine switch off, key held against engine switch and engine switch pushed*3 Pulse generation
(see waveform 2)
G36-11 (SWIL) - G36-5 (GND) B - W-B Illumination signal Light control switch off → tail Below 2 V → 9 to 14 V
G36-14 (VC5) - G36-8 (AGND) P - GR Power supply Engine switch off, 30 seconds or more after door opened or closed and brake pedal*1 or clutch pedal*2 not depressed Below 1 V
G36-14 (VC5) - G36-8 (AGND) P - GR Power supply Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed Pulse generation
(see waveform 3)

*1: for Automatic Transmission

*2: for Manual Transmission


HINT:

*3: Remove the key battery before performing this inspection.



e.

Inspect using an oscilloscope.

i.
B051052E49
2.823,0.771 3.177,0.958 0.354,0.188 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G36-9 (TXCT) - G36-8 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed


ii.
B051053E26
2.813,0.771 3.177,0.99 0.365,0.219 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G36-10 (CODE) - G36-8 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key held against engine switch and engine switch pushed*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007E01
2.887,0.987 3.231,1.157 0.343,0.170 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G36-14 (VC5) - G36-8 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed




CHECK CERTIFICATION ECU


U169647E04
2.438,0.542 2.719,0.719 0.281,0.177 10 false G38 4.677,0.542 4.958,0.719 0.281,0.177 10 false G39

a.

Disconnect the G38 ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G38-1 (+B) - G38-15 (E) V - W-B +B power supply Always 11 to 14 V
G38-17 (CUTB) - G38-15 (E) L - W-B +B power supply Always 11 to 14 V
G38-16 (IG) - G38-15 (E) W - W-B Ignition power supply Engine switch off → on (IG) Below 1 V → 11 to 14 V
G38-15 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the G38 ECU connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G38-2 (IND) - G38-15 (E) G - W-B Security indicator output Engine switch off → on (IG) Pulse generation
→ Below 2 V
G38-11 (SWIL) - G38-36 (AGND) B - GR Illumination signal Light control switch off Below 2 V
G38-11 (SWIL) - G38-36 (AGND) B - GR Illumination signal Light control switch tail 9 to 14 V
G38-12 (TXCT) - G38-36 (AGND) W - GR Engine switch TXCT output Engine switch off, 30 seconds or more after door opened or closed and brake pedal*1 or clutch pedal*2 not depressed Below 1 V
G38-12 (TXCT) - G38-36 (AGND) W - GR Engine switch TXCT output Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed Pulse generation
(see waveform 1)
G38-13 (CODE) - G38-36 (AGND) V - GR Engine switch CODE input Key not in cabin Below 1 V
G38-13 (CODE) - G38-36 (AGND) V - GR Engine switch CODE input Engine switch off, key held against engine switch and engine switch pushed*3 Pulse generation
(see waveform 2)
G38-28 (VC5) - G38-36 (AGND) P - GR Engine switch power supply Engine switch off, 30 seconds or more after door opened or closed and brake pedal*1 or clutch pedal*2 not depressed Below 1 V
G38-28 (VC5) - G38-36 (AGND) P - GR Engine switch power supply Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed Pulse generation
(see waveform 3)
G38-36 (AGND) - Body ground GR - Body ground Engine switch ground Always Below 1 Ω

*1: for Automatic Transmission

*2: for Manual Transmission


HINT:

*3: Remove the key battery before performing this inspection.



e.

Inspect using an oscilloscope.

i.
B051052E50
2.823,0.792 3.146,0.99 0.323,0.198 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G38-12 (TXCT) - G38-36 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed


ii.
B051053E27
2.823,0.76 3.208,0.979 0.385,0.219 11 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G38-13 (CODE) - G38-36 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key held against engine switch and engine switch pushed*

HINT:

*: Remove the key battery before performing this inspection.



iii.
B216007E01
2.887,0.987 3.231,1.157 0.343,0.170 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection G38-28 (VC5) - G38-36 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin and 30 seconds or less after engine switch pushed




CHECK ID CODE BOX


U169629E02
3.469,0.104 3.792,0.333 0.323,0.229 10 false G37

a.

Disconnect the G37 box connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G37-1 (+B) - G37-8 (GND) V - W-B +B power supply Always 11 to 14 V
G37-8 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the G37 box connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G37-5 (EFII) - G37-8 (GND) SB - W-B ECM input signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected Pulse generation
(see waveform 1)
G37-6 (EFIO) - G37-8 (GND) W - W-B ECM output signal Engine switch off → on (IG) Below 1 V → Pulse generation
(see waveform 2)


e.

Inspect using an oscilloscope.

i.
B229710E01
0.129,0.732 0.459,0.877 0.33,0.145 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G37-5 (EFII) - G37-8 (GND)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected


ii.
B237527E01
2.809,0.515 3.177,0.683 0.368,0.168 10 GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G37-6 (EFIO) - G37-8 (GND)
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Engine switch on (IG)




CHECK STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)


U169876E02
1.594,0.125 1.927,0.333 0.333,0.208 10 false G35

a.

Disconnect the G35 ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G35-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
G35-6 (IG2) - G35-1 (GND) W - W-B IG2 signal input Engine switch off → on (IG) Below 1 V → 11 to 14 V
G35-7 (B) - Body ground G - Body ground Power source Always 11 to 14 V



CHECK POWER MANAGEMENT CONTROL ECU


U169650E02
2.479,0.438 2.813,0.604 0.333,0.167 10 false G50 4.583,0.427 4.875,0.594 0.292,0.167 10 false G51

a.

Disconnect the G51 ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G51-1 (AM22) - Body ground B - Body ground Battery power Always 11 to 14 V
G51-2 (AM21) - Body ground B - Body ground Battery power Always 11 to 14 V
G51-5 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
G51-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω



CHECK ECM (for 1GR-FE)


U149279E04
1.198,0.188 1.479,0.396 0.281,0.208 10 false G55 2.031,0.188 2.354,0.385 0.323,0.198 10 false G56 3.344,0.188 3.677,0.385 0.333,0.198 10 false C34 4.052,0.198 4.354,0.385 0.302,0.188 10 false C35 4.833,0.188 5.156,0.365 0.323,0.177 10 false C36 5.719,0.188 6.031,0.375 0.313,0.188 10 false C37

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G56-8 (IMO) - Body ground*1
G56-20 (IMO) - Body ground*2
SB - Body ground ID code box output signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected Pulse generation
(see waveform 1)
G56-10 (IMI) - Body ground*1
G56-14 (IMI) - Body ground*2
W - Body ground ID code box input signal Engine switch off → Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected Below 1 V → Pulse generation
(see waveform 2)

*1: for Automatic Transmission

*2: for Manual Transmission



b.

Inspect using an oscilloscope.

i.
B229710E01
0.129,0.732 0.459,0.877 0.33,0.145 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G56-8 (IMO) - Body ground*1
G56-20 (IMO) - Body ground*2
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected

*1: for Automatic Transmission

*2: for Manual Transmission



ii.
B237527E01
2.809,0.515 3.177,0.683 0.368,0.168 10 GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G56-10 (IMI) - Body ground*1
G56-14 (IMI) - Body ground*2
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected

*1: for Automatic Transmission

*2: for Manual Transmission





CHECK ECM (for 2TR-FE)


U169867E02
0.708,0.458 1.094,0.615 0.385,0.156 10 false C153 2.094,0.448 2.479,0.604 0.385,0.156 10 false C154 3.542,0.448 3.927,0.604 0.385,0.156 10 false C155 4.844,0.448 5.229,0.604 0.385,0.156 10 false G181 6.135,0.448 6.521,0.604 0.385,0.156 10 false G180

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G181-9 (IMO) - Body ground SB - Body ground ID code box output signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected Pulse generation
(see waveform 1)
G181-10 (IMI) - Body ground W - Body ground ID code box input signal Engine switch off → Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected Below 1 V → Pulse generation
(see waveform 2)


b.

Inspect using an oscilloscope.

i.
B229710E01
0.129,0.732 0.459,0.877 0.33,0.145 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G181-9 (IMO) - Body ground
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected


ii.
B237527E01
2.809,0.515 3.177,0.683 0.368,0.168 10 GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G181-10 (IMI) - Body ground
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected




CHECK ECM (for 1KD-FTV)


U170622E03
1.198,0.177 1.479,0.365 0.281,0.188 10 false G57 2.021,0.177 2.323,0.396 0.302,0.219 10 false G58 3.323,0.177 3.635,0.375 0.313,0.198 10 false C90 4.073,0.188 4.417,0.417 0.344,0.229 10 false C91 4.813,0.177 5.156,0.385 0.344,0.208 10 false C92 5.698,0.177 6.052,0.417 0.354,0.24 10 false C93

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G58-29 (IMO) - Body ground SB - Body ground ID code box output signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected Pulse generation
(see waveform 1)
G58-28 (IMI) - Body ground W - Body ground ID code box input signal Engine switch off → Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected Below 1 V → Pulse generation
(see waveform 2)


b.

Inspect using an oscilloscope.

i.
B229710E01
0.129,0.732 0.459,0.877 0.33,0.145 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G58-29 (IMO) - Body ground
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected


ii.
B237527E01
2.809,0.515 3.177,0.683 0.368,0.168 10 GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G58-28 (IMI) - Body ground
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected




CHECK ECM (for 1GD-FTV)


U169464E02
0.615,0.5 1.125,0.708 0.51,0.208 10 false C149 1.74,0.5 2.25,0.708 0.51,0.208 10 false C150 2.927,0.5 3.438,0.708 0.51,0.208 10 false C151 3.969,0.5 4.479,0.708 0.51,0.208 10 false C152 5.115,0.5 5.625,0.708 0.51,0.208 10 false G184 6.177,0.51 6.688,0.719 0.51,0.208 10 false G185

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G185-17 (IMO) - Body ground SB - Body ground ID code box output signal Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected Pulse generation
(see waveform 1)
G185-16 (IMI) - Body ground W - Body ground ID code box input signal Engine switch off → Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected Below 1 V → Pulse generation
(see waveform 2)


b.

Inspect using an oscilloscope.

i.
B229710E01
0.129,0.732 0.459,0.877 0.33,0.145 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection G185-17 (IMO) - Body ground
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected


ii.
B237527E01
2.809,0.515 3.177,0.683 0.368,0.168 10 GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection G185-16 (IMI) - Body ground
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after engine switch first turned on (IG) after battery disconnected and connected