Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the ID code box (immobiliser code ECU); 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the ID code box (immobiliser code ECU) and ECM is different and an engine start is attempted.

Before troubleshooting for this DTC, make sure no certification ECU DTCs are output. If output, troubleshoot the certification ECU DTCs first.

DTC Code DTC Detection Condition Trouble Area
B2799 One of the following conditions is met:
·

An error in the communication between the ECM and ID code box (immobiliser code ECU).

·

An error in the communication lines.

·

The communication ID is different during communication with the ID code box (immobiliser code ECU).


·

Harness or connector

·

ECM

·

ID code box (immobiliser code ECU)



WIRING DIAGRAM

B365295E16
0.833,2.198 1.24,2.385 0.406,0.188 10 false ECM 5.542,2.198 7.042,2.552 1.5,0.354 10 false ID Code Box (Immobiliser Code Box) 1.417,1.281 1.74,1.542 0.323,0.26 10 false IMI 1.375,0.521 1.771,0.76 0.396,0.24 10 false IMO 5.854,0.531 6.25,0.771 0.396,0.24 10 false EFII 5.854,1.281 6.281,1.51 0.427,0.229 10 false EFIO 5.594,1.177 5.792,1.354 0.198,0.177 10 false 6 5.594,0.406 5.792,0.604 0.198,0.198 10 false 5 1.76,0.385 3.604,0.656 1.844,0.271 10 false 8*1, 20*2, 29*3, 9*4, 17*5 1.76,1.146 3.771,1.396 2.01,0.25 10 false 10*1, 14*2, 28*3, 10*4, 16*5 0.844,2.031 3.208,2.25 2.365,0.219 10 false G56*1, *2, G58*3, G181*4, G185*5 5.5,2.021 7.021,2.24 1.521,0.219 10 false G37 0.063,2.865 3.156,3.156 3.094,0.292 10 false *1: for 1GR-FE (for Automatic Transmission) 2.948,3.177 4.917,3.5 1.969,0.323 10 false *5: for 1GD-FTV 0.073,3.458 1.604,3.781 1.531,0.323 10 false *3: for 1KD-FTV 2.948,2.875 4.875,3.198 1.927,0.323 10 false *4: for 2TR-FE 0.063,3.146 3.146,3.479 3.083,0.333 10 false *2: for 1GR-FE (for Manual Transmission)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ID code box (immobiliser code ECU) or ECM, refer to the Service Bulletin.


PROCEDURE

2.CHECK FOR DTC

OK

NG

3.REGISTER ECU COMMUNICATION ID
3.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (Refer to the Service Bulletin).



NEXT

4.CLEAR DTC
5.CHECK FOR DTC

OK

END (ECU COMMUNICATION ID IS NOT REGISTERED CORRECTLY)

NG

6.CHECK CONNECTION OF CONNECTOR
6.CHECK CONNECTION OF CONNECTOR
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.




OK

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)

NG

CONNECT CONNECTOR CORRECTLY

7.CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)
a.

Disconnect the G37 ID code box (immobiliser code ECU) connector.


b.

Disconnect the G56*1, G58*2, G181*3 or G185*4 ECM connector.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 2TR-FE

*4: for 1GD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE (for Automatic Transmission)
Tester Connection Condition Specified Condition
G37-5 (EFII) - G56-8 (IMO) Always Below 1 Ω
G37-6 (EFIO) - G56-10 (IMI) Always Below 1 Ω
G37-5 (EFII) or G56-8 (IMO) - Body ground Always 10 kΩ or higher
G37-6 (EFIO) or G56-10 (IMI) - Body ground Always 10 kΩ or higher

for 1GR-FE (for Manual Transmission)
Tester Connection Condition Specified Condition
G37-5 (EFII) - G56-20 (IMO) Always Below 1 Ω
G37-6 (EFIO) - G56-14 (IMI) Always Below 1 Ω
G37-5 (EFII) or G56-20 (IMO) - Body ground Always 10 kΩ or higher
G37-6 (EFIO) or G56-14 (IMI) - Body ground Always 10 kΩ or higher

for 1KD-FTV
Tester Connection Condition Specified Condition
G37-5 (EFII) - G58-29 (IMO) Always Below 1 Ω
G37-6 (EFIO) - G58-28 (IMI) Always Below 1 Ω
G37-5 (EFII) or G58-29 (IMO) - Body ground Always 10 kΩ or higher
G37-6 (EFIO) or G58-28 (IMI) - Body ground Always 10 kΩ or higher

for 2TR-FE
Tester Connection Condition Specified Condition
G37-5 (EFII) - G181-9 (IMO) Always Below 1 Ω
G37-6 (EFIO) - G181-10 (IMI) Always Below 1 Ω
G37-5 (EFII) or G181-9 (IMO) - Body ground Always 10 kΩ or higher
G37-6 (EFIO) or G181-10 (IMI) - Body ground Always 10 kΩ or higher

for 1GD-FTV
Tester Connection Condition Specified Condition
G37-5 (EFII) - G185-17 (IMO) Always Below 1 Ω
G37-6 (EFIO) - G185-16 (IMI) Always Below 1 Ω
G37-5 (EFII) or G185-17 (IMO) - Body ground Always 10 kΩ or higher
G37-6 (EFIO) or G185-16 (IMI) - Body ground Always 10 kΩ or higher




OK

8.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE ECM

NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID (Refer to the Service Bulletin).



NEXT

10.CLEAR DTC
11.CHECK FOR DTC

OK

END (ECM IS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)