Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  Security Indicator Light Circuit  


DESCRIPTION

When the engine immobiliser system is set, the security indicator flashes continuously, but does not illuminate if the engine immobiliser system is not set.


WIRING DIAGRAM

B242452E04
0.99,1.984 3.095,2.150 2.105,0.166 10 Security Indicator Light Assembly 1.252,1.137 2.715,1.300 1.463,0.163 10 Security Indicator Light 3.218,1.433 3.384,1.619 0.166,0.186 10 E 3.152,0.891 3.427,1.077 0.275,0.186 10 LP 3.427,1.383 3.789,1.569 0.362,0.186 10 5 3.426,0.841 3.732,1.026 0.306,0.186 10 2 4.733,0.849 4.927,1.034 0.194,0.186 10 2 5.072,2.055 5.428,2.241 0.356,0.186 10 G38 0.993,1.817 1.293,2.003 0.300,0.186 10 H23 4.935,0.97 5.259,1.156 0.324,0.186 10 IND 5.072,2.205 6.155,2.394 1.083,0.189 10 Certification ECU

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU, refer to the Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
a.

Check that the security indicator light illuminates when operating it with the Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DATA LIST / ACTIVE TEST).

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Immobiliser Indicator Security indicator light ON/OFF The test is possible when the following conditions are met:
·

The key is in the cabin.

·

The engine switch is on (IG).



OK:

Security indicator light can be turned on and off using the intelligent tester.




OK

NG

2.INSPECT SECURITY INDICATOR LIGHT ASSEMBLY
2.INSPECT SECURITY INDICATOR LIGHT ASSEMBLY
a.
B238374E01
0.737,0.653 0.954,0.830 0.217,0.177 10 LP 0.848,1.608 0.978,1.785 0.130,0.177 10 E 1.003,0.735 1.106,0.735 1.106,0.735 1.506,0.967 false 1.004,1.701 1.106,1.701 1.106,1.701 1.507,1.469 false

Remove the security indicator light assembly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL).


b.

Apply battery voltage between the terminals of the security indicator light assembly and check that the security indicator light illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (LP)
Battery negative (-) → 5 (E)
Security indicator light illuminates




OK

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - CERTIFICATION ECU AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - CERTIFICATION ECU AND BODY GROUND)
a.

Disconnect the H23 light connector.


b.

Disconnect the G38 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H23-2 (LP) - G38-2 (IND) Always Below 1 Ω
H23-5 (E) - Body ground Always Below 1 Ω
H23-2 (LP) or G38-2 (IND) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR