Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  B278A  Short to GND in Immobiliser System Power Source Circuit  


DESCRIPTION

This DTC is stored when the engine switch power source supply line is open or shorted.

DTC Code DTC Detection Condition Trouble Area
B278A The engine switch power source supply line is open or shorted.
·

Harness or connector

·

Engine switch

·

Certification ECU



WIRING DIAGRAM

B153714E21
0.854,2.035 1.816,2.238 0.961,0.203 10 Engine Switch 0.854,1.867 1.186,2.070 0.332,0.203 10 G36 1.363,0.77 1.838,1.019 0.475,0.249 10 VC5 1.247,1.242 1.701,1.617 0.453,0.375 10 AGND 1.749,0.673 1.998,0.856 0.249,0.183 10 14 1.749,1.157 1.927,1.330 0.179,0.173 10 8 5.189,0.673 5.438,0.856 0.249,0.183 10 28 5.189,1.157 5.438,1.330 0.249,0.173 10 36 5.472,1.234 5.926,1.609 0.453,0.375 10 AGND 5.282,2.055 6.466,2.225 1.184,0.170 10 Certification ECU 5.282,1.868 6.466,2.038 1.184,0.170 10 G38 5.472,0.78 5.760,1.158 0.288,0.378 10 VC5

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU, refer to the Service Bulletin.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ENGINE SWITCH)
a.

Disconnect the G38 ECU connector.


b.

Disconnect the G36 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-28 (VC5) - G36-14 (VC5) Always Below 1 Ω
G38-36 (AGND) - G36-8 (AGND)
G38-28 (VC5) or G36-14 (VC5) - Body ground Always 10 kΩ or higher
G38-36 (AGND) or G36-8 (AGND) - Body ground




OK

2.CHECK CERTIFICATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CERTIFICATION ECU
a.

Using an oscilloscope, check the waveform.

B450051E01
1.844,0.323 2.302,0.646 0.458,0.323 1.292,1.979 1.708,1.563 true 2.844,1.958 2.531,1.563 true 0.854,0.375 1.167,0.573 0.313,0.198 10 false *a 1.938,0.406 2.396,0.604 0.458,0.198 10 false G36 0.979,1.948 1.438,2.146 0.458,0.198 10 false VC5 2.854,1.958 3.469,2.156 0.615,0.198 10 false AGND 6.146,1.479 6.76,1.677 0.615,0.198 10 false GND

Measurement Condition
Item Content
Tester Connection G36-14 (VC5) - G36-8 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, and 30 seconds or less after engine switch pushed

OK:

Waveform is output normally (refer to illustration).


Text in Illustration
*a Component with harness connected
(Engine Switch)

HINT:

If replacing the Engine Switch, refer to the procedures below.





OK

REPLACE ENGINE SWITCH

NG

REPLACE CERTIFICATION ECU