Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261055 ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/ Entry and Start System)  Certification ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to the certification ECU.

WIRING DIAGRAM

B217872E04
0.633,0.615 1.441,0.789 0.809,0.174 10 from Battery 0.633,1.096 1.441,1.270 0.809,0.174 10 from Battery 0.633,1.651 1.608,1.826 0.975,0.174 10 from IG2 Relay 3.668,0.801 4.172,0.981 0.503,0.179 10 ECU-B 3.624,1.297 4.173,1.476 0.549,0.179 10 SMART 3.687,1.834 3.982,1.999 0.295,0.165 10 IGN 5.835,0.629 6.269,0.812 0.434,0.184 10 CUTB 5.835,1.11 6.047,1.293 0.211,0.184 10 +B 5.835,1.67 6.033,1.854 0.198,0.184 10 IG 5.835,2.221 5.950,2.405 0.114,0.184 10 E 5.522,0.552 5.715,0.703 0.193,0.151 10 17 5.522,1.579 5.715,1.730 0.193,0.151 10 16 5.597,1.042 5.716,1.193 0.119,0.151 10 1 5.522,2.111 5.715,2.263 0.193,0.151 10 15 5.621,3.015 5.920,3.176 0.299,0.161 10 G38 5.593,3.202 6.735,3.362 1.142,0.161 10 Certification ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)
a.
U169643E02
0.99,0.885 0.708,1.667 false 0.344,0.885 0.594,1.5 false 0.323,1.438 0.573,1.667 false 3.177,1.281 2.938,1.5 false 0.25,0.156 0.469,0.344 0.219,0.188 10 false *a 1.625,0.51 1.927,0.667 0.302,0.156 10 false G38 1.021,0.792 1.469,0.979 0.448,0.188 10 false CUTB 0.104,0.813 0.365,0.969 0.26,0.156 10 false +B 3.208,1.198 3.406,1.438 0.198,0.24 10 false E 0.104,1.323 0.313,1.51 0.208,0.188 10 false IG

Disconnect the G38 ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G38-1 (+B) - Body ground Always 11 to 14 V
G38-16 (IG) - Body ground Engine switch off Below 1 V
G38-16 (IG) - Body ground Engine switch on (IG) 11 to 14 V
G38-17 (CUTB) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-15 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Certification ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR