If the communication line (EFIO-IMI) to the ID code box is stuck on HI output, the ECM stores this DTC.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B279A | The communication line (EFIO-IMI) between the ECM and the ID code box (immobiliser code ECU) is stuck on HI output. | ·
Harness or connector ·
ID code box (immobiliser code ECU) ·
ECM |
When replacing the ID code box (immobiliser code ECU) or ECM, refer to the Service Bulletin.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR).
If DTCs other than DTC B279A are output, troubleshoot those DTCs first.
| Result | Proceed to |
|---|---|
| No DTC is not output | A |
| DTC B279A and other DTCs are output | B |
| DTC B279A is output | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Disconnect the G37 ID code box (immobiliser code ECU) connector.
Disconnect the G56*1, G58*2, G181*3 or G185*4 ECM connector.
*1: for 1GR-FE
*2: for 1KD-FTV
*3: for 2TR-FE
*4: for 1GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-6 (EFIO) - G56-10 (IMI) | Always | Below 1 Ω |
| G37-6 (EFIO) or G56-10 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-6 (EFIO) - G56-14 (IMI) | Always | Below 1 Ω |
| G37-6 (EFIO) or G56-14 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-6 (EFIO) - G58-28 (IMI) | Always | Below 1 Ω |
| G37-6 (EFIO) or G58-28 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-6 (EFIO) - G181-10 (IMI) | Always | Below 1 Ω |
| G37-6 (EFIO) or G181-10 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-6 (EFIO) - G185-16 (IMI) | Always | Below 1 Ω |
| G37-6 (EFIO) or G185-16 (IMI) - Body ground | Always | 10 kΩ or higher |
OK
NG
Using an oscilloscope, check the waveform.
| *A | for 1GR-FE | *B | for Automatic Transmission |
| *C | for Manual Transmission | *D | for 1KD-FTV |
| *E | for 2TR-FE | *F | for 1GD-FTV |
| *a | Component with harness connected
(ECM) |
- | - |
| Item | Content |
|---|---|
| Tester Connection | G56-10 (IMI) - Body ground*1
G56-14 (IMI) - Body ground*2 G58-28 (IMI) - Body ground*3 G181-10 (IMI) - Body ground*4 G185-16 (IMI) - Body ground*5 |
| Tool Setting | 10 V/DIV., 100 ms./DIV. |
| Condition | Engine switch on (IG) |
*1: for 1GR-FE (for Automatic Transmission)
*2: for 1GR-FE (for Manual Transmission)
*3: for 1KD-FTV
*4: for 2TR-FE
*5: for 1GD-FTV
Waveform is output normally (refer to illustration).
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for 1GR-FE) | B |
| OK (for 1KD-FTV) | C |
| OK (for 2TR-FE) | D |
| OK (for 1GD-FTV) | E |
A
B
C
D
E
Disconnect the G37 ID code box (immobiliser code ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-1 (+B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G37-8 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to ID Code Box [Immobiliser Code ECU]) |
OK
NG
Temporarily replace the ECM with a new one.
for 1GR-FE (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL)
for 1KD-FTV (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL)
for 2TR-FE (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>ECM>REMOVAL)
for 1GD-FTV (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL)
NEXT
Register the ECU communication ID (Refer to the Service Bulletin).
NEXT
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)>DTC CHECK / CLEAR).
DTC B279A is not output.
OK
NG