Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › 2015.06–2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261067 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


U169796E02
3.385,0.667 3.708,0.823 0.323,0.156 10 false G74

a.

Disconnect the G74 transponder key ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G74-1 (+B) - G74-5 (GND) Input P - W-B Battery Always 11 to 14 V +B
G74-2 (IG) - G74-5 (GND) Input W - W-B Ignition switch signal Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
G74-3 (KSW) - G74-5 (GND) Input G - W-B Unlock warning switch signal No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key in ignition key cylinder Below 1 Ω
G74-5 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G74-7 (CTY) - Body ground Input R - Body ground*1
B - Body ground*2
Door courtesy switch (for driver side) signal Driver side door closed 10 kΩ or higher -
Driver side door open Below 1 Ω

·

*1: for LHD

·

*2: for RHD



c.

Reconnect the G74 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G74-8 (IND) - G74-5 (GND) Output G - W-B Security indicator signal No key in ignition key cylinder, or 20 sec. elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Key in ignition key cylinder (immobiliser system unset) Below 1 V
G74-9 (D) - G74-5 (GND) Input/Output W - W-B DLC3 communication Without communication Below 1 V -
During communication Pulse generation
G74-4 (ANT1) - G74-5 (GND) Input/Output R - W-B Transponder key amplifier power source No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 1)
G74-15 (ANT2) - G74-5 (GND) Input/Output G - W-B Transponder key amplifier communication signal No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 2)
G74-12 (EFII) - G74-5 (GND) Output SB - W-B ECM input signal Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
-
G74-13 (EFIO) - G74-5 (GND) Input W - W-B ECM output signal Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 4)


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909E01
5.76,0.854 6.219,1.052 0.458,0.198 10 GND

Tester Connection G74-4 (ANT1) - G74-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910E01
5.75,0.854 6.208,1.052 0.458,0.198 10 GND

Tester Connection G74-15 (ANT2) - G74-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


iii.

Waveform 3 (Reference)

B325134E02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection G74-12 (EFII) - G74-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B333259E02
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.31,1.366 3.505,1.539 0.195,0.173 10 *b 3.119,1.352 3.314,1.525 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection G74-13 (EFIO) - G74-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON




CHECK ECM (for 1KD-FTV)


U170601E02
0.729,0.833 1.021,1.01 0.292,0.177 10 false G57 1.688,0.823 1.979,1 0.292,0.177 10 false G58 3.219,0.833 3.51,1.01 0.292,0.177 10 false C90 4.125,0.833 4.417,1.01 0.292,0.177 10 false C91 5.031,0.823 5.323,1 0.292,0.177 10 false C92 6.115,0.833 6.406,1.01 0.292,0.177 10 false C93

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
C93-1 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C93-12 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C93-13 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G57-23 (BATT) - C93-1 (E1) Input L - BR +B power supply Always 11 to 14 V -
G57-24 (+B) - C93-1 (E1) Input W - BR IG power supply Ignition switch ON 11 to 14 V -
G57-17 (+B2) - C93-1 (E1) Input W - BR IG power supply Ignition switch ON 11 to 14 V -
G58-29 (IMO) - C93-1 (E1) Input SB - BR Transponder key ECU assembly communication input Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
G58-28 (IMI) - C93-1 (E1) Output W - BR Transponder key ECU assembly communication output Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
-

a.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258E02
0.826,1.172 1.250,1.393 0.424,0.221 10 GND 2.722,1.275 2.971,1.505 0.248,0.230 10 *a 2.909,1.275 3.157,1.496 0.248,0.221 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection G58-29 (IMO) - C93-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259E02
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.31,1.366 3.505,1.539 0.195,0.173 10 *b 3.119,1.352 3.314,1.525 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection G58-28 (IMI) - C93-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON




CHECK ECM (for 2TR-FE)


U169479E02
2.01,0.385 2.396,0.531 0.385,0.146 10 false C154 3.427,0.375 3.833,0.552 0.406,0.177 10 false C155 4.865,0.396 5.281,0.552 0.417,0.156 10 false G181 6.115,0.396 6.51,0.552 0.396,0.156 10 false G180 0.74,0.385 1.094,0.531 0.354,0.146 10 false C153 1.052,2.271 1.406,2.417 0.354,0.146 10 false C153 2.521,2.26 2.906,2.406 0.385,0.146 10 false C154 4.156,2.26 4.573,2.417 0.417,0.156 10 false G181 5.583,2.26 5.979,2.417 0.396,0.156 10 false G180 0.052,0 2.969,0.271 2.917,0.271 12 false for Automatic Transmission: 0.052,1.854 2.969,2.125 2.917,0.271 12 false for Manual Transmission:

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
C153-3 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C153-1 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C153-2 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G180-3 (BATT) - C153-3 (E1) Input L - BR +B power supply Always 11 to 14 V -
G180-1 (+B) - C153-3 (E1) Input W - BR IG power supply Ignition switch ON 11 to 14 V -
G180-2 (+B2) - C153-3 (E1) Input W - BR IG power supply Ignition switch ON 11 to 14 V -
G181-9 (IMO) - C153-3 (E1) Input SB - BR Transponder key ECU assembly communication input Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
G181-10 (IMI) - C153-3 (E1) Output W - BR Transponder key ECU assembly communication output Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
-

a.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258E02
0.826,1.172 1.250,1.393 0.424,0.221 10 GND 2.722,1.275 2.971,1.505 0.248,0.230 10 *a 2.909,1.275 3.157,1.496 0.248,0.221 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection G181-9 (IMO) - C153-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259E02
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.31,1.366 3.505,1.539 0.195,0.173 10 *b 3.119,1.352 3.314,1.525 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection G181-10 (IMI) - C153-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON




CHECK ECM (for 5L-E)


U169865E02
1.146,0.135 1.531,0.292 0.385,0.156 10 false C161 2.708,0.135 3.094,0.292 0.385,0.156 10 false C162 4.313,0.135 4.698,0.292 0.385,0.156 10 false G183 5.833,0.135 6.219,0.292 0.385,0.156 10 false G182

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
C161-5 (E1) - Body ground - BR - Body ground Ground Always Below 1 Ω -
C161-7 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
C161-6 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G183-2 (BATT) - C161-5 (E1) Input L - BR +B power supply Always 11 to 14 V -
G183-1 (+B) - C161-5 (E1) Input W - BR IG power supply Ignition switch ON 11 to 14 V -
G182-18 (IMO) - C161-5 (E1) Input SB - BR Transponder key ECU assembly communication input Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
G182-19 (IMI) - C161-5 (E1) Output W - BR Transponder key ECU assembly communication output Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
-

a.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258E02
0.826,1.172 1.250,1.393 0.424,0.221 10 GND 2.722,1.275 2.971,1.505 0.248,0.230 10 *a 2.909,1.275 3.157,1.496 0.248,0.221 10 *b

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection G182-18 (IMO) - C161-5 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259E02
0.848,1.231 1.218,1.405 0.370,0.173 10 GND 3.31,1.366 3.505,1.539 0.195,0.173 10 *b 3.119,1.352 3.314,1.525 0.195,0.173 10 *a

Text in Illustration
*a Approximately 160 ms *b Approximately 270 ms

Tester Connection G182-19 (IMI) - C161-5 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON