When an open or short circuit is detected in the antenna coil built into the transponder key coil, the transponder key ECU assembly stores this DTC.
| DTC No. | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
|---|---|---|---|
| B2784 | The antenna coil in the transponder key coil is open/shorted. | ·
Harness or connector ·
Transponder key coil ·
Transponder key ECU assembly |
Insert the key into the ignition key cylinder. |
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2784 | Antenna Coil Status |
If the transponder key ECU assembly is replaced, refer to the Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
DTC B2784 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Check that the connectors are properly connected to the transponder key coil.
NEXT
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
DTC B2784 is not output.
OK
NG
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Transponder Key Coil) |
*b | Waveform 1 |
| *c | Waveform 2 | - | - |
| Item | Content |
|---|---|
| Tester Connection | G189-1 (ANT1) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms/DIV |
| Condition | Within 3 seconds of inserting key into ignition key cylinder |
| Item | Content |
|---|---|
| Tester Connection | G189-5 (ANT2) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms/DIV |
| Tool Setting | Within 3 seconds of inserting key into ignition key cylinder |
Waveform is similar to that shown in the illustration.
OK
NG
Replace the transponder key ECU assembly with a new one.
Refer to the Service Bulletin.
Key ID code registration is necessary when replacing the transponder key ECU assembly.
Refer to the Service Bulletin.
NEXT
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
DTC B2784 is not output.
OK
NG
Disconnect the G74 transponder key ECU assembly connector.
Disconnect the G189 transponder key coil connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G74-4 (ANT1) - G189-1 (ANT1) | Always | Below 1 Ω |
| G74-15 (ANT2) - G189-5 (ANT2) | Always | Below 1 Ω |
| G74-4 (ANT1) - Body ground | Always | 10 kΩ or higher |
| G189-1 (ANT1) - Body ground | Always | 10 kΩ or higher |
| G74-15 (ANT2) - Body ground | Always | 10 kΩ or higher |
| G189-5 (ANT2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the transponder key ECU assembly with a new one.
Refer to the Service Bulletin.
Key ID code registration is necessary when replacing the transponder key ECU assembly.
Refer to the Service Bulletin.
NEXT
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
DTC B2784 is not output.
OK
NG