Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261067 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.

WIRING DIAGRAM

B242452E09
0.423,1.8 2.534,1.965 2.111,0.166 10 Security Indicator Light Assembly 1.252,1.137 2.715,1.300 1.463,0.163 10 Security Indicator Light 3.228,1.433 3.353,1.619 0.125,0.186 10 E 3.152,0.891 3.427,1.077 0.275,0.186 10 LP 3.427,1.383 3.789,1.569 0.362,0.186 10 5 3.426,0.841 3.732,1.026 0.306,0.186 10 2 4.721,0.856 4.840,1.042 0.119,0.186 10 8 4.615,2.055 6.539,2.241 1.924,0.186 10 G74 0.425,1.68 0.725,1.866 0.300,0.186 10 H23 4.935,0.97 5.259,1.156 0.324,0.186 10 IND 4.615,2.205 6.696,2.394 2.081,0.189 10 Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to the Service Bulletin.

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Immobiliser
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -

OK:

Security indicator light can be turned on and off using the GTS.




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - SECURITY INDICATOR LIGHT ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - SECURITY INDICATOR LIGHT ASSEMBLY AND BODY GROUND)
a.

Disconnect the G74 transponder key ECU assembly connector.


b.

Disconnect the H23 security indicator light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G74-8 (IND) - H23-2 (LP) Always Below 1 Ω
H23-5 (E) - Body ground Always Below 1 Ω
G74-8 (IND) - Body ground Always 10 kΩ or higher
H23-2 (LP) - Body ground Always 10 kΩ or higher




OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)
a.

Connect the G74 transponder key ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H23-2 (LP) - Body ground Key not in ignition key cylinder Pulse generation
Key in ignition key cylinder Below 1 V




OK

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY