Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › 2015.06–2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261067 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B279A Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Harness or connector

·

ECM

·

Transponder key ECU assembly


Turn the ignition switch to ON and wait 6 seconds.

Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

B365296E10
1.052,1.958 2.969,2.156 1.917,0.198 10 false G58*1, G181*2, G182*3 1.063,2.146 1.458,2.365 0.396,0.219 10 false ECM 5.25,2.156 6.656,2.469 1.406,0.313 10 false Transponder Key ECU Assembly 1.479,1.104 1.781,1.344 0.302,0.24 10 false IMI 5.469,1.104 5.833,1.26 0.365,0.156 10 false EFIO 5.229,1 5.458,1.208 0.229,0.208 10 false 13 1.792,1 3.792,1.198 2,0.198 10 false 28*1, 10*2, 19*3 5.25,1.958 6.771,2.177 1.521,0.219 10 false G74 0.094,2.688 1.833,2.979 1.74,0.292 10 false *1: for 1KD-FTV 0.094,3.24 1.625,3.563 1.531,0.323 10 false *3: for 5L-E 0.094,2.969 1.792,3.302 1.698,0.333 10 false *2: for 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

2.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

OK:

DTC B279A is not output.


Result:
Result Proceed to
NG A
OK B




A

3.CHECK CONNECTION OF CONNECTOR

B

3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.




OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G74 transponder key ECU assembly connector.


b.

Disconnect the G58*1, G181*2 or G182*3 ECM connector.


·

*1: for 1KD-FTV

·

*2: for 2TR-FE

·

*3: for 5L-E


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G58-28 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G58-28 (IMI) - Body ground Always 10 kΩ or higher

for 2TR-FE
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G181-10 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G181-10 (IMI) - Body ground Always 10 kΩ or higher

for 5L-E
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G182-19 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G182-19 (IMI) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 1KD-FTV
Tester Connection Condition Specified Condition
G58-28 (IMI) - Body ground Always Below 1 V

for 2TR-FE
Tester Connection Condition Specified Condition
G181-10 (IMI) - Body ground Always Below 1 V

for 5L-E
Tester Connection Condition Specified Condition
G182-19 (IMI) - Body ground Always Below 1 V




OK

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to the Service Bulletin.




NEXT

6.CLEAR DTC
7.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

OK:

DTC B279A is not output.


Result:
Result Proceed to
OK A
NG (for 1KD-FTV) B
NG (for 2TR-FE) C
NG (for 5L-E) D




A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C

D