Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) › 2015.06–2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261067 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the door control transmitter assembly and transponder key ECU assembly match, the engine immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B365295E15
0.844,2.208 1.26,2.417 0.417,0.208 10 false ECM 5.5,2.229 6.927,2.604 1.427,0.375 10 false Transponder Key ECU Assembly 1.417,1.281 1.719,1.448 0.302,0.167 10 false IMI 1.375,0.531 1.719,0.708 0.344,0.177 10 false IMO 5.854,0.51 6.229,0.698 0.375,0.188 10 false EFII 5.854,1.292 6.292,1.49 0.438,0.198 10 false EFIO 5.594,1.167 5.823,1.354 0.229,0.188 10 false 13 5.563,0.417 5.771,0.604 0.208,0.188 10 false 12 1.74,1.146 3.583,1.417 1.844,0.271 10 false 28*1, 10*2, 19*3 1.74,0.406 3.75,0.656 2.01,0.25 10 false 29*1, 9*2, 18*3 0.844,2.031 3.208,2.25 2.365,0.219 10 false G58*1, G181*2, G182*3 5.5,2.063 7.021,2.281 1.521,0.219 10 false G74 0.063,2.896 1.802,3.188 1.74,0.292 10 false *1: for 1KD-FTV 0.063,3.479 1.594,3.802 1.531,0.323 10 false *3: for 5L-E 0.063,3.177 1.76,3.51 1.698,0.333 10 false *2: for 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to the Service Bulletin.

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

Result:
Result Proceed to
NG (for SFI System) A
NG (for ECD System) B
OK C




A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

4.CHECK WHETHER ENGINE STARTS

C

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Read the Data List according to the display on the GTS.

Engine and ECT (ECM)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser fuel cut / ON or OFF ON: Immobiliser fuel cut on
OFF: Immobiliser fuel cut off
-

OK:

OFF is displayed after the ignition switch to ON.


Result:
Result Proceed to
NG A
OK B




A

4.CHECK WHETHER ENGINE STARTS

B

4.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result:
Result Proceed to
NG A
OK B




A

5.CHECK ECM (TERMINAL IMI)

B

5.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

U169863E01
1.403,0.172 1.790,0.331 0.388,0.159 10 G57 0.142,0.172 0.630,0.431 0.488,0.259 12 *A 0.142,0.35 0.630,0.609 0.488,0.259 10 *a 0.142,1.797 0.630,2.057 0.488,0.259 10 *a 0.142,3.429 0.630,3.688 0.488,0.259 10 *a 0.142,5.063 0.630,5.322 0.488,0.259 10 *a 0.142,1.65 0.630,1.909 0.488,0.259 12 *B 0.142,3.268 0.630,3.528 0.488,0.259 12 *C 0.142,4.887 0.630,5.146 0.488,0.259 12 *D 2.17,0.172 2.558,0.331 0.388,0.158 10 G58 3.207,0.172 3.595,0.331 0.388,0.158 10 C90 3.943,0.172 4.330,0.331 0.388,0.158 10 C91 4.678,0.172 5.066,0.331 0.388,0.158 10 C92 5.428,0.172 5.815,0.331 0.388,0.158 10 C93 1.193,1.65 1.580,1.809 0.388,0.159 10 C153 2.299,1.65 2.687,1.809 0.388,0.159 10 C154 2.412,1.417 2.799,1.575 0.388,0.159 10 IMI 3.448,1.65 3.836,1.809 0.388,0.159 10 C155 4.618,1.65 5.006,1.809 0.388,0.159 10 G181 5.676,1.65 6.064,1.809 0.388,0.159 10 G180 1.585,3.268 1.973,3.427 0.388,0.159 10 C153 2.804,3.268 3.191,3.427 0.388,0.159 10 C154 4.198,3.268 4.585,3.427 0.388,0.159 10 G181 5.375,3.268 5.762,3.427 0.388,0.159 10 G180 1.585,4.887 1.973,5.045 0.388,0.158 10 C161 2.804,4.887 3.191,5.045 0.388,0.158 10 C162 2.323,7.868 2.710,8.027 0.388,0.158 10 *b 3.459,7.902 3.846,8.061 0.388,0.158 10 *e 3.473,8.254 3.860,8.412 0.388,0.158 10 *d 3.389,6.806 3.776,6.964 0.388,0.158 10 *c 0.972,7.811 1.467,8.077 0.495,0.266 10 GND 4.198,4.887 4.585,5.045 0.388,0.158 10 G183 5.375,4.887 5.762,5.045 0.388,0.158 10 G182 3.311,7.837 3.311,8.329 3.311,8.329 3.437,8.329 false 2.213,1.187 2.26,1.477 2.26,1.477 2.386,1.477 false 5.042,2.923 5.430,3.081 0.388,0.159 10 IMI 4.833,2.456 4.891,2.984 4.891,2.984 5.017,2.984 false 4.617,4.54 5.004,4.698 0.388,0.159 10 IMI 4.408,4.073 4.466,4.601 4.466,4.601 4.592,4.601 false 6.075,6.277 6.463,6.436 0.388,0.159 10 IMI 5.866,5.81 5.924,6.338 5.924,6.338 6.05,6.338 false

Text in Illustration
*A for 1KD-FTV *B for 2TR-FE (for Automatic Transmission)
*C for 2TR-FE (for Manual Transmission) *D for 5L-E
*a Component with harness connected
(ECM)
*b Waveform 1
*c Waveform 2 *d Approximately 160 ms
*e Approximately 270 ms - -

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
G58-28 (IMI) - Body ground*1
G181-10 (IMI) - Body ground*2
G182-19 (IMI) - Body ground*3
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


·

*1: for 1KD-FTV

·

*2: for 2TR-FE

·

*3: for 5L-E


Result:
Result Proceed to
Normal waveform A
Waveform 1 not output, or has abnormal wavelength or shape B
Waveform 2 not output, or has abnormal wavelength or shape C




A

6.CHECK ECM (TERMINAL IMO)

B

12.CHECK HARNESS AND CONNECTOR ((TRANSPONDER KEY ECU ASSEMBLY - ECM)

C

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
6.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

U169864E01
1.403,0.172 1.790,0.331 0.388,0.159 10 G57 0.142,0.172 0.630,0.431 0.488,0.259 12 *A 0.142,0.35 0.630,0.609 0.488,0.259 10 *a 0.142,1.797 0.630,2.057 0.488,0.259 10 *a 0.142,3.429 0.630,3.688 0.488,0.259 10 *a 0.142,5.063 0.630,5.322 0.488,0.259 10 *a 0.142,1.65 0.630,1.909 0.488,0.259 12 *B 0.142,3.268 0.630,3.528 0.488,0.259 12 *C 0.142,4.887 0.630,5.146 0.488,0.259 12 *D 2.17,0.172 2.558,0.331 0.388,0.158 10 G58 3.207,0.172 3.595,0.331 0.388,0.158 10 C90 3.943,0.172 4.330,0.331 0.388,0.158 10 C91 4.678,0.172 5.066,0.331 0.388,0.158 10 C92 5.428,0.172 5.815,0.331 0.388,0.158 10 C93 1.193,1.65 1.580,1.809 0.388,0.159 10 C153 2.299,1.65 2.687,1.809 0.388,0.159 10 C154 2.342,1.417 2.729,1.575 0.388,0.159 10 IMO 3.448,1.65 3.836,1.809 0.388,0.159 10 C155 4.618,1.65 5.006,1.809 0.388,0.159 10 G181 5.676,1.65 6.064,1.809 0.388,0.159 10 G180 1.585,3.268 1.973,3.427 0.388,0.159 10 C153 2.804,3.268 3.191,3.427 0.388,0.159 10 C154 4.198,3.268 4.585,3.427 0.388,0.159 10 G181 5.375,3.268 5.762,3.427 0.388,0.159 10 G180 1.585,4.887 1.973,5.045 0.388,0.158 10 C161 2.804,4.887 3.191,5.045 0.388,0.158 10 C162 2.937,6.834 3.325,6.993 0.388,0.158 10 *b 3.039,7.902 3.426,8.061 0.388,0.158 10 *d 3.081,8.254 3.468,8.412 0.388,0.158 10 *c 0.972,7.811 1.467,8.077 0.495,0.266 10 GND 4.198,4.887 4.585,5.045 0.388,0.158 10 G183 5.375,4.887 5.762,5.045 0.388,0.158 10 G182 2.919,7.838 2.919,8.329 2.919,8.329 3.045,8.329 false 2.143,1.187 2.19,1.477 2.19,1.477 2.316,1.477 false 5.144,2.923 5.531,3.081 0.388,0.159 10 IMO 4.935,2.456 4.992,2.984 4.992,2.984 5.118,2.984 false 4.722,4.54 5.110,4.698 0.388,0.159 10 IMO 4.513,4.073 4.571,4.601 4.571,4.601 4.697,4.601 false 6.198,6.277 6.585,6.436 0.388,0.159 10 IMO 5.989,5.81 6.047,6.338 6.047,6.338 6.173,6.338 false

Text in Illustration
*A for 1KD-FTV *B for 2TR-FE (for Automatic Transmission)
*C for 2TR-FE (for Manual Transmission) *D for 5L-E
*a Component with harness connected
(ECM)
*b Waveform
*c Approximately 160 ms *d Approximately 270 ms

Measurement Condition:
Tester Connection Condition Tool Setting Specified Condition
G58-29 (IMO) - Body ground*1
G181-9 (IMO) - Body ground*2
G182-18 (IMO) - Body ground*3
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


·

*1: for 1KD-FTV

·

*2: for 2TR-FE

·

*3: for 5L-E


Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape B




A

7.REGISTER ECU COMMUNICATION ID

B

9.REPLACE ECM
7.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to the Service Bulletin.




NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.




OK

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

NG

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
9.REPLACE ECM
a.

Temporarily replace the ECM with a new one.




NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to the Service Bulletin.




NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result:
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 1KD-FTV) C
NG (for 5L-E) D




A

END (ECM WAS DEFECTIVE)

B

C

D

12.CHECK HARNESS AND CONNECTOR ((TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the G74 transponder key ECU assembly connector.


b.

Disconnect the G58*1, G181*2 or G182*3 ECM connector.

·

*1: for 1KD-FTV

·

*2: for 2TR-FE

·

*3: for 5L-E



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G58-28 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G58-28 (IMI) - Body ground Always 10 kΩ or higher

for 2TR-FE
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G181-10 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G181-10 (IMI) - Body ground Always 10 kΩ or higher

for 5L-E
Tester Connection Condition Specified Condition
G74-13 (EFIO) - G182-19 (IMI) Always Below 1 Ω
G74-13 (EFIO) or G182-19 (IMI) - Body ground Always 10 kΩ or higher




OK

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to the Service Bulletin.




NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.


Result:
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 1KD-FTV) C
NG (for 5L-E) D




A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C

D