Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the meter. This circuit provides two types of power sources; one is a constant power source mainly used as a backup power source, and the other is an IG power source mainly used for signal transmission. The constant power source is mainly used as a backup power source for the meter CPU, however, it is also used for CAN communication. If a voltage of 12 V is not applied to terminal IG+ when turn the ignition switch to ON, the indicator will not operate.

WIRING DIAGRAM

E175183E03
1.171,1.616 2.139,1.789 0.968,0.173 10 from IG2 Relay 1.348,0.866 2.141,1.040 0.792,0.173 10 from Battery 3.521,1.013 3.974,1.187 0.453,0.173 10 ECU-B 3.504,1.754 4.039,1.927 0.535,0.173 10 GAUGE 5.578,0.683 5.767,0.832 0.188,0.149 10 26 5.889,0.872 6.038,1.021 0.149,0.149 10 B 5.889,1.608 6.149,1.757 0.260,0.149 10 IG+ 5.889,2.371 6.149,2.520 0.260,0.149 10 E2 5.889,2.878 6.149,3.027 0.260,0.149 10 EP 5.568,2.886 5.788,3.035 0.220,0.149 10 G6 5.291,4.737 7.148,4.913 1.857,0.177 10 Combination Meter Assembly 5.584,2.2 5.761,2.349 0.178,0.149 10 21 5.624,2.685 5.750,2.834 0.126,0.149 10 1 5.564,2.385 5.791,2.534 0.226,0.149 10 G6 5.561,1.603 5.774,1.752 0.213,0.149 10 G6 5.563,0.863 5.783,1.012 0.220,0.149 10 G6 5.578,1.412 5.767,1.560 0.188,0.149 10 28

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170596C01
0.802,1.188 0.667,0.802 0.667,0.802 0.573,0.802 false 1.302,1.417 1.406,1.865 1.406,1.865 1.51,1.865 false 1.5,1.406 1.708,1.708 1.708,1.708 1.802,1.708 false 0.813,1.417 0.708,1.771 0.708,1.771 0.573,1.771 false 0.125,0.073 0.302,0.24 0.177,0.167 10 false *a 0.271,1.198 0.542,1.417 0.271,0.219 10 false G6 0.313,1.688 0.656,1.948 0.344,0.26 10 false E2 1.531,1.792 1.875,2.042 0.344,0.25 10 false B 1.833,1.615 2.313,1.885 0.479,0.271 10 false IG+ 0.302,0.708 0.771,0.99 0.469,0.281 10 false EP

Disconnect the combination meter assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-21 (E2) - Body ground Always Below 1 Ω
G6-1 (EP) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G6-28 (IG+) - Body ground Ignition switch ON 11 to 14 V
G6-26 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly


OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR