Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

In this circuit, the meter CPU receives engine speed signals from the ECM. The meter CPU displays the engine speed calculated based on the data received from the ECM.

WIRING DIAGRAM

E349711E01
0.146,0.146 1.979,0.344 1.833,0.198 10 false except 5L-E: 1.375,2.635 1.833,2.833 0.458,0.198 10 false ECM 4.219,2.646 6.417,2.885 2.198,0.24 10 false Combination Meter Assembly 0.75,3.385 2.563,3.594 1.813,0.208 10 false : CAN Communication Line

E298936E20
5.198,1.063 5.656,1.26 0.458,0.198 10 false S 4.958,0.938 5.417,1.135 0.458,0.198 10 false 34 2.073,0.969 2.531,1.167 0.458,0.198 10 false 7 1.604,1.073 2.063,1.271 0.458,0.198 10 false TACH 1.323,1.781 1.781,1.979 0.458,0.198 10 false G182 1.333,1.927 2.563,2.313 1.229,0.385 10 false ECM 5.167,1.781 5.625,1.979 0.458,0.198 10 false G6 5.167,1.927 6.438,2.292 1.271,0.365 10 false Combination Meter Assembly 0.135,0.094 1.51,0.292 1.375,0.198 10 false for 5L-E:

PROCEDURE

1.CHECK ENGINE TYPE
a.

Check the engine type.

Result
Result Proceed to
except 5L-E A
for 5L-E B



A

2.CHECK CAN COMMUNICATION SYSTEM

B

7.PERFORM ACTIVE TEST USING GTS (TACHO METER OPERATION)
2.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.




iv.

for RHD without Entry and Start System (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN communication DTC is not output. A
CAN communication DTC is output. (for LHD, with Entry and Start System) B
CAN communication DTC is output. (for LHD, without Entry and Start System) C
CAN communication DTC is output. (for RHD, with Entry and Start System) D
CAN communication DTC is output. (for RHD, without Entry and Start System) E




A

3.PERFORM ACTIVE TEST USING GTS (TACHO METER OPERATION)

B

C

D

E

3.PERFORM ACTIVE TEST USING GTS (TACHO METER OPERATION)
a.

Using the GTS, perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Tacho Meter Operation Tachometer OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000* (rpm) -

*: for 1GR-FE, 2TR-FE

OK:

Tachometer indication is normal.





OK

4.READ VALUE USING GTS (ENGINE RPM)

NG

4.READ VALUE USING GTS (ENGINE RPM)
a.

Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Rpm Engine speed/Min.: 0 rpm, Max.: 12750 rpm 600 to 700 rpm (When idling) If the data received from the ECM exceeds the range that can be displayed on the meter, the meter continues to display the maximum value of the range.

OK:

Engine speed displayed on the intelligent tester is almost the same as the tachometer indication.



b.

Record the engine speed displayed on the intelligent tester.

HINT:

Check the engine speed when the engine is fully warmed up and the air conditioning and all electrical accessories are off.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

5.READ VALUE USING GTS (ENGINE SPEED)
5.READ VALUE USING GTS (ENGINE SPEED)
a.

Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Speed Engine speed/Min.: 0 rpm, Max.: 16383 rpm 600 to 700 rpm (When idling) -

OK:

Engine speed displayed on GTS is almost same as actual engine speed.


Result
Result Proceed to
OK A
NG (for Gasoline Engine) B
NG (for Diesel Engine) C

HINT:
·

for 1GR-FE:

If it is necessary to refer to the SFI system, refer to the following procedures (See page ).

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

for 2TR-FE:

If it is necessary to refer to the SFI system, refer to the following procedures (See page ).

Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

for 1KD-FTV:

If it is necessary to refer to the ECD system, refer to the following procedures (See page ).

Click hereEngine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

for 1GD-FTV

If it is necessary to refer to the ECD system, refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1GD-FTV, w/ Urea SCR System:

If it is necessary to refer to the ECD system, refer to the following procedures (See page ).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING





A

6.CHECK ECM

B

GO TO SFI SYSTEM

C

GO TO ECD SYSTEM

6.CHECK ECM

b.

Check that the operation of the tachometer returns to normal.

OK:

The operation of the tachometer returns to normal.




OK

END (ECM IS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY

7.PERFORM ACTIVE TEST USING GTS (TACHO METER OPERATION)
a.

Using the GTS, perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Tacho Meter Operation Tachometer OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000* (rpm) -

*: for 1GR-FE, 2TR-FE

OK:

Tachometer indication is normal.





OK

8.CHECK COMBINATION METER ASSEMBLY (ENGINE SPEED SIGNAL)

NG

REPLACE COMBINATION METER ASSEMBLY

8.CHECK COMBINATION METER ASSEMBLY (ENGINE SPEED SIGNAL)
a.
U170656E01
0.839,0.655 1.065,0.810 0.225,0.156 10 G6 2.077,1.729 2.567,2.219 false 2.601,2.167 2.729,2.323 0.128,0.156 10 S 3.039,3.499 3.376,3.655 0.336,0.156 10 GND 0.375,1.11 0.545,1.266 0.170,0.156 10 *a 0.375,2.571 0.545,2.727 0.170,0.156 10 *b

Remove the combination meter assembly with the connector(s) still connected (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Content
Tester Connection G6-34 (S) - Body ground
Tool Setting 5 V/DIV, 20 ms./DIV
Vehicle Condition Idling with warm engine

HINT:

As the engine speed increases, the wavelength shortens.


OK:

The waveform displayed is as shown in the illustration.


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)
*b Speed Signal Waveform



OK

REPLACE COMBINATION METER ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the G182 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-34 (S) - G182-7 (TACH) Always Below 1 Ω
G6-34 (S) or G182-7 (TACH) - Body ground Always 10 kΩ or higher




OK

10.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK ECM
a.

Replace the ECM with a new or normally functioning one (See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ECM>REMOVAL).


b.

Check that the operation of the tachometer returns to normal.

OK:

The operation of the tachometer returns to normal.




OK

END (ECM IS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY