Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM D

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  INITIALIZATION  


OIL MAINTENANCE INFORMATION MODE RESET OPERATION (except Analog Meter, Segment Display Type)


NOTICE:
·

When "OIL MAINTENANCE REQUIRED SOON" is displayed, change the engine oil and perform this procedure.

·

After the engine oil is changed, perform this procedure so that "OIL MAINTENANCE REQUIRED SOON" does not display.



HINT:
·

The oil change maintenance system displays "OIL MAINTENANCE REQUIRED SOON" in the multi-information display to inform the driver that it is time to change the oil based on the distance driven

·

The ODO/TRIP switch is in the light control rheostat.



a.

Turn the ignition switch to ON, and use the ODO/TRIP switch to change the screen display to TRIP A.


b.

Turn the ignition switch to off.


c.

While holding in the ODO/TRIP switch, turn the ignition switch to ON.


d.

After a 5 second count, reset will end.

E349668E01
0.583,0.896 1.896,1.313 1.313,0.417 10 false 5 seconds until reset process completes 2.938,0.896 4.271,1.438 1.333,0.542 10 false 4 seconds until reset process completes 5.323,0.896 6.604,1.438 1.281,0.542 10 false 3 seconds until reset process completes 5.354,2.333 6.656,2.75 1.302,0.417 10 false 2 seconds until reset process completes 2.969,2.271 4.271,2.792 1.302,0.521 10 false 1 second until reset process completes 1.031,2.385 1.49,2.583 0.458,0.198 10 false End

NOTICE:
·

If the ignition switch is turned off during the reset operation, reset mode will be canceled.

·

If the ODO/TRIP switch is turned off during the reset operation, reset mode will be canceled.





OIL MAINTENANCE INFORMATION MODE RESET OPERATION (for Analog Meter, Segment Display Type)


NOTICE:
·

When the oil maintenance warning light is illuminated, change the engine oil and perform this procedure.

·

After the engine oil is changed, perform this procedure so that the oil maintenance warning light does not turn on.



a.

Turn the ignition switch to ON, and use the ODO/TRIP switch to change the screen display to TRIP A.


b.

Turn the ignition switch to off.


c.

While holding in the ODO/TRIP switch, turn the ignition switch to ON.


d.

After a 5 second count, reset will end.

NOTICE:
·

If the ignition switch is turned off during the reset operation, reset mode will be canceled.

·

If the ODO/TRIP switch is turned off during the reset operation, reset mode will be canceled.





TIMING BELT INFORMATION MODE RESET OPERATION (for Optitron Meter)


NOTICE:
·

When "T-BELT MAINTENANCE REQUIRED" is displayed, replace the timing belt and perform this procedure.

·

After the timing belt is replaced, perform this procedure so that "T-BELT MAINTENANCE REQUIRED" does not display.



HINT:
·

The timing belt maintenance system displays "T-BELT MAINTENANCE REQUIRED" in the multi-information display to inform the driver that it is time to replace the timing belt based on the distance driven.

·

The ODO/TRIP switch is in the light control rheostat.



a.

Turn the ignition switch to ON, and use the ODO/TRIP switch to change the screen display to TRIP B.


b.

Turn the ignition switch to off.


c.
E205067

While holding in the ODO/TRIP switch, turn the ignition switch to ON.

HINT:

"RESETTING T-BELT MAINTENANCE DATA" will be displayed.



d.

Press and hold the ODO/TRIP switch for 5 seconds or more.

HINT:

A 5 second count will begin on the display.


E349670E01
0.677,0.938 1.771,1.344 1.094,0.406 10 false 5 seconds until prepared for reset 3.052,0.906 4.156,1.313 1.104,0.406 10 false 4 seconds until prepared for reset 5.438,0.896 6.51,1.396 1.073,0.5 10 false 3 seconds until prepared for reset 5.469,2.313 6.594,2.698 1.125,0.385 10 false 2 seconds until prepared for reset 3.063,2.313 4.177,2.708 1.115,0.396 10 false 1 second until prepared for reset


e.
E205069

After the 5 second count finishes, "RESETTING OF T-BELT MAINTENANCE DATA NOW POSSIBLE" is displayed and T-BELT reset mode is complete.


f.

While "RESETTING OF T-BELT MAINTENANCE DATA NOW POSSIBLE" is displayed, turn the ODO/TRIP switch from off to on.

HINT:

While "RESETTING OF T-BELT MAINTENANCE DATA NOW POSSIBLE" is displayed, if the ODO/TRIP switch is not turned from off to on, the normal display will return.



g.

After the ODO/TRIP switch is turned on, enter the setting mode and change to T-BELT display mode.

HINT:

The T-BELT display mode will display the previously set value (the interval until the next time the timing belt needs to be replaced). However, the first time this is performed, the default setting from when the vehicle is delivered (150000 km or 90000 miles) is displayed.



h.

Change the set value by repeatedly turning the ODO/TRIP switch on and off (the value must be changed within 5 seconds). (procedure A)

E157121E13
1.094,0.375 1.896,0.521 0.802,0.146 10 false Unit = "Mile" 1.094,1.552 1.896,1.698 0.802,0.146 10 false Unit = "km" 1.635,0.854 5.844,1.052 4.208,0.198 10 false The last designated value → 1 → 2 → 3.....................18 → 19 → 20 1.635,2.052 5.844,2.25 4.208,0.198 10 false The last designated value → 1 → 2 → 3.....................18 → 19 → 20 2.24,1.115 3.063,1.26 0.823,0.146 10 false (Default = 9) 2.281,2.427 3.208,2.573 0.927,0.146 10 false (Default = 15)

HINT:

Perform this procedure only when changing the previously set value.


NOTICE:

If the ODO/TRIP switch is not turned from on to off for 30 seconds or more during this step, the previously set value will be maintained and the TRIP B display will return (reset will not complete).



i.

When the display changes to the desired setting, press the ODO/TRIP switch for 5 seconds or more to finish setting mode. (procedure B)


j.
E205070

The set value is stored in the EEPROM, "RESETTING OF T-BELT MAINTENANCE DATA COMPLETE" is displayed (for 1 second), and reset mode is completed. (procedure C)

HINT:

If the set value is not stored in the EEPROM, "RESETTING OF T-BELT MAINTENANCE DATA COMPLETE" is not displayed and the normal display returns.


NOTICE:
·

When not changing the previously set value, do not perform the operations in procedure A above, only perform procedures B and C.

·

If the starter signal is received during the reset operation, reset mode is canceled and cannot be resumed until the ignition switch is turned off and ON again.





TIMING BELT INFORMATION MODE RESET OPERATION (for Analog Meter)


NOTICE:
·

When the T-BELT indicator light is illuminated, replace the timing belt and perform this procedure.

·

After the timing belt is replaced, perform this procedure so that the T-BELT indicator light does not turn on.



HINT:
·

The timing belt maintenance system turns on the T-BELT indicator light to inform the driver that it is time to replace the timing belt based on the distance driven.



a.

Turn the ignition switch to ON, and use the ODO/TRIP switch to change the screen display to TRIP B.


b.

Turn the ignition switch to off.


c.

While holding in the ODO/TRIP switch, turn the ignition switch to ON and check that the T-BELT indicator light blinks.


d.

Press and hold the ODO/TRIP switch for 5 seconds or more.

HINT:

If the ODO/TRIP switch is released (off is detected) within 5 seconds, the ODO/TRIP display, indicator display, and the integrated value will return to the state before the reset operation began.



e.

After the ODO/TRIP switch is turned off, turn the ODO/TRIP switch on again within 5 seconds.


f.

After the ODO/TRIP switch is turned on, enter the setting mode and change to T-BELT display mode.


g.

Change the set value in increments by turning the ODO/TRIP switch (the value must be changed within 5 seconds). (procedure A)

E157121E14
1.094,0.375 1.896,0.521 0.802,0.146 10 false Unit = "Mile" 1.094,1.552 1.896,1.698 0.802,0.146 10 false Unit = "km" 1.635,0.854 5.844,1.052 4.208,0.198 10 false The last designated value → 1 → 2 → 3.....................18 → 19 → 20 1.635,2.052 5.844,2.25 4.208,0.198 10 false The last designated value → 1 → 2 → 3.....................18 → 19 → 20 2.281,1.208 3.104,1.354 0.823,0.146 10 false (Default = 9) 2.281,2.427 3.208,2.573 0.927,0.146 10 false (Default = 15)

HINT:

Perform this procedure only when changing the previously set value.


NOTICE:

If the ODO/TRIP switch is not turned from on to off for 30 seconds or more during this step, the previously set value will be maintained and the TRIP B display will return (reset will not complete).



h.

When the display changes to the desired setting, press the ODO/TRIP switch for 5 seconds or more to finish setting mode. (procedure B)


i.

The ODO display area changes to the TRIP B display, the warning indicator turns off simultaneously and reset mode is completed. (procedure C)

NOTICE:

When not changing the previously set value, do not perform the operations in procedure A above, only perform procedures B and C.




SEDIMENT/FILTER WARNING LIGHT RESET OPERATION (w/ SEDIMENT/FILTER warning light)


HINT:
·

When the fuel system warning light blinks, drain accumulated water from the fuel filter assembly.

·

When the fuel system warning light illuminates, follow the procedures below to reset the combination meter assembly.




b.

Disconnect the A76 level warning switch connector.


c.

Turn the ignition switch to ON


d.

Wait 3 seconds.


e.

Reconnect the A76 level warning switch connector within 57 seconds.


f.

Make sure that the SEDIMENT/FILTER warning light turns off 3 seconds after the connector is reconnected.